Quickstart

This is a Light Dimmer Switch for XXXQFrequencyName. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:
1. Turn Off power to the light bulb socket2. Screw in the light bulb3. Place your network controller into inclusion mode by following the controller manufacturer's instructions4. Turn On power to the light bulb.If successful, the LED light bulb will flash twice to indicate successful inclusion.5. If the controller/gateway shows it was a fail, repeat the procedure.Note: If Inclusion still fails after the 2nd attempt, you need to first RESET the dt Smart Bulb before repeating the above steps.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from Z-Wave Alliance Product data and may be incomplete. Please refer to the Manufacturers Manual for more information.

Product Description

Smart LED light bulb with Z-Wave radio.- Control lights remotely and save energy- Compatible with smart home systems supporting Z-Wave- 60 Watt equivalent light (750 lumens)- Consumes only 9 watts of power- 2700K soft light with frosted glass - Instant ON and fully dimmable- Functions as a Z-Wave signal repeater- Very simple to include in your network- Z-Wave Plus certified

Reset to factory default You may manually reset the light bulb as follows:1.Flick the wall switch OFF-ON 4 times within 4 seconds. 2. The dt Smart Bulb will flash twice after Reset is successful.Use this procedure only in the event that the network primary controller is lost or otherwise inoperable.
Inclusion 1. Turn Off power to the light bulb socket2. Screw in the light bulb3. Place your network controller into inclusion mode by following the controller manufacturer's instructions4. Turn On power to the light bulb.If successful, the LED light bulb will flash twice to indicate successful inclusion.5. If the controller/gateway shows it was a fail, repeat the procedure.Note: If Inclusion still fails after the 2nd attempt, you need to first RESET the dt Smart Bulb before repeating the above steps.
Exclusion 1. Turn off power to the light bulb socket2. Follow the network controller instruction to place your network controller into exclusion mode to remove the dt light bulb from the network.3. After being prompted by the network controller, turn On power to the light bulb.If successful, the LED light bulb will flash twice to indicate successful inclusion.
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 The dtSmart Bulb supports Group 1 with up to ve devices for lifeline communication. Group 1 must be assigned the Node ID of the controller to which unsolicited notications will be sent. The Z-Wave controller should set this association automatically after inclusion. Lifeline association only supports the manual reset event. Please refer to the instructions manual of your remote controller or gateway for detail procedures on how these function can be set.

Configuration Parameters

Parameter 1: Dim level when the light bulb is turned On

You may select the Dim level whenever the light is turned back ON to be either full brightness (100% dim level) or be the same as the last dim setting when the light was previously ON.
Size: 1 Byte, Default Value: 0

Setting Description
0 The brightness level will be resume to full brightness when the dt Smart Bulb is turned ON every time.
1 The brightness level will maintain same dim level as the last setting when the dt Smart Bulb is turned ON again.

Technical Data

Hardware Platform ZM5202
Device Type Light Dimmer Switch
Network Operation Always On Slave
Firmware Version HW: 255
Z-Wave Version 6.51.02
Certification ID ZC10-14100003
Z-Wave Product Id 0x020E.0x4754.0x3038
Frequency XXfrequency
Maximum transmission power XXantenna
U.S. / Canada / MexicoLight Dimmer Switch