Z-Wave Europe
POPP Keypad + ABUS HomeTec Pro Z-Wave
SKU: ZWUE700045W
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
POPP Keypad + ABUS HomeTec Pro – the innovative door opener for your smart home
The POPP Keypad in combination with the ABUS HomeTec Pro Z-Wave provides its owner more comfort, control and flexibility. With the pluggable Z-Wave door lock drive, apartments or front doors can be smartly opened and locked.
Never worry about forgotten keys anymore. Never lock yourself out again. With the Keypad each of your family members gets an own access code.
The installation of both products is comfortable and easy. It only requires a door cylinder with emergency function, which has a projection of 7 to 12 mm on the inside of the door. Both devices are battery powered. They can be installed with a few simple steps without any wiring.
This article contains 2 products:
POPP Keypad - POPE700045
- up to 20 different programmable Pincodes
- Pin codes with 4 to 10 digits
- Aluminium casing
- For outdoor use and installation (IP44)
- Colored status LED and acoustical feedback
- Integrated doorbell button for the association with a doorbell (On/Off Switch)
- Pin Codes can be used to trigger different scenes in a gateway or control a doorlock directly
- Wireless technology: Z-Wave Plus EU frequency 868,42 Mhz
- Package content: 1x Keypad, 4x AAA batteries, 1x adhesive strip for wallmounting
- Power supply: 4x AAA batteries or 5V DC power adapter (not included)
HomeTec Pro Z-Wave - ABUE3010 (silver of white color)
- For houses, apartments, offices and service rooms
- Easy, flexible and uncomplicated installation
- Installation with adhesive mounting plate, locking ring or screws
- Locking and unlocking with buttons or manually via locking wheel
- Precisely Locks, unlocks and opens door latch
- Adjustable RPM and torque
- Wireless technology: Z-Wave Plus EU frequency 868,42 Mhz
- Package content: 1x Hometec Pro Z-Wave, 4x AA batteries, Installation plate
- Power supply: 4xAA batteries
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| EAN | 4251295701424 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.