Quickstart

This is a Notification Sensor for XXXQFrequencyName. To run this device please insert fresh 1 * built in LiMnO2 batteries. To run this device please make sure the internal battery is fully charged. Strips is delivered in "auto-add" mode. Follow the process below to add Strips in a Z-Wave network.
1. Start the add mode on the Z-Wave controller. See the controller’s manual.
2. Remove both magnets from Strips. Strips blinks twice to confirm the command and successful addition.
3. A long LED blink indicates that the add process was successful
4. The Z-Wave controller application should now allow you to monitor your Strips sensor status.
5. Move the squared magnet as shown in the picture . Check that the Z-Wave system indicates the status correctly



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

Strips by Sensative is an ultra-thin magnetic sensor designed to monitor windows and doors for your safety. It´s so thin that it can be mounted invisibly in the tiny gap between the frame and the door or window.
It is as easy to mount as a sticker using Strips"s adhesive tape.
Strips is Z-Wave plus compliant and can be used with any existing Z-Wave smarthome systems.

Installation

Reset to factory default 1. Place the round magnet at the rounded edge of Strips.
2. When the LED blinks, move the magnet away. Repeat 3 times in total within 10 seconds.
3. On the 3rd repetition, leave the magnet at the rounded edge for 10s.
4. A long LED signal indicates success.
Inclusion 1. Remove both magnets from Strips. Strips blinks twice to confirm the command and successful addition.
2. A long LED blink indicates that the add process was successful
3. The Z-Wave controller application should now allow you to monitor your Strips sensor status.
4. Move the squared magnet as shown in the picture . Check that the Z-Wave system indicates the status correctly
6. If the Z-Wave system do not respond, it may be needed to change Strips’ notification type.

Manual add:
1. Set the controller to add mode (See your controller’s manual).
2. Place the round magnet at the rounded edge of Strips. When the LED blinks, move the magnet away. Repeat 3 times in total within 10 seconds.
3. A long LED blink indicates that the add process was successful.
Exclusion Place the round magnet at the rounded edge of Strips. When the LED blinks, move the magnet away. Repeat 3 times in total within 10 seconds. A long LED blink indicates that the remove process was successful.
NIF XXXNIF
Wakeup Wake up Strips manually for Z-Wave communication: 1. Place the round magnet at the rounded edge of Strips. 2. When the LED blinks, move the magnet away. 3. Repeat 3 times in total within 10 seconds.
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 1 Z-Wave Plus Lifeline

Configuration Parameters

Parameter 1: Notification type

User can use this configuration parameter to change the notification type compatible with their gatewaycontroller.
Size: 1 Byte, Default Value: 1

Setting Description
0 Binary Sensor report
1 Notification report
2 Basic report

Parameter 2: LED indication

LED On during specific event detected (ex. door opened) else if the parameter value is 0, LED will be turned OFF for the specific event detected.
Size: 1 Byte, Default Value: 1

Setting Description
0 Specific event indication (ex. door opened) Off
1 On

Technical Data

Dimensions 195 x 15 x 3 mm
Weight 13 gr
Hardware Platform ZM5101
EAN 7350088520017
Battery Type 1 * built in LiMnO2
Device Type Notification Sensor
Network Operation Reporting Sleeping Slave
Z-Wave Version 6.51.06
Certification ID ZC10-16045049
Z-Wave Product Id 0x019A.0x0003.0x0003
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeNotification Sensor