Quickstart

This is a Z-Wave Controller for XXXQFrequencyName. To run this device please connect it to your mains power supply.

1.     Connect the HUB to your local network using Ethernet cable.
2.     Power up the controller. After up to 2 minutes the HUB is ready to use and the white LED will breathe normal. Now you can connect your computer or mobile device to the new WIFI Popp-xxxx (xxxx=last 4 digits of MAC address displayed on device label, WIFI-password on label, too). Attention: For security reasons, the initial configuration is available via WIFI only. Later, you will have more options.
3.     Point your browser to http://192.168.115.1:8083. If you use a mobile device, install and start the Popp HUB app (Use the QR code on page 4). 
4.     The welcome screen displays your unique device ID. Remember it for remote access! Define your access password for the default login name ‘admin’ and your email for password recovery, set your time zone and LAN access (otherwise you can only access using find.popp.eu and using WIFI).
5.     In case there is a firmware update you will see a message screen. Please confirm and update the firmware. Make sure not to un-power the device during the firmware update.
6.     Now you can access your controller from outside your home, too, using the service find.popp.eu. Use DEVICE_ID/LOGIN (e.g. 12345/admin) and your password.
7.     Start adding Z-Wave devices and apps and have fun. To add your first Z-Wave device, go to ->Configuration ->Devices ->Z-Wave ->Add New and follow the instructions.
8.     You can later change your device‘s time zone and allow access to the hub user interface via the Ethernet address. Please go to ->Setup ->Applications ->Active and change settings in "Time Zone and Access from WAN" app.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

Sensors, switches, thermostats, cameras and many devices more will make you home intelligent. But all these components need a central controller.

The second-generation POPP HUB is a slim and compact IP smart home gateway, equipped with Z-Wave wireless technology. Therewith you can control your whole home automation network via remote switches, smartphone, desktop and tablet pc. Inside one network the POPP HUB controls up to 230 Z-Wave components manufacturer-independently and allows management of direct connections (associations) between the devices. These associations can be used also without a central gateway.

The latest POPP HUB hardware generation is still more flexible. Beside already installed WiFi and Z-Wave technologies the HUB can integrate further technologies such as EnOcean via internal and external USB ports. The POPP HUB enables you to control your home centralized and flexible ? and without any wiring effort.

The HUB works with Z-Way, the fist Z-Wave Plus certified Z-Wave controller software, which also connects devices with different technologies with each other.

The POPP HUB is focused on easy operation and reliable security architecture. Therewith it is one of the most secure smart home gateways generally. Thanks to the integrated device database and step-by-step instructions any new smart home device can be connected quick and easy. The POPP HUB?s big advantage is its capability to integrate all certified Z-Wave devices with all of theirs functions. Other gateways block some device functions by itself.

By using so-called apps from the continuously growing app store, you can setup a lot of automation scenes in no time. So, you can switch your sockets time scheduled, dim lights depending on current brightness or heat up your home to your comfortable temperature by only one push of a button.

With the free POPP HUB smartphone and tablet app, you can control your home also from outside.

Detailed instructions on the gateway can be found under the following link: Manual

Reset to factory default

1.      Pressing down the WPS button
2.      Press reset button
3.      Keep WPS button further pressed until the white LED starts blinking fast (ca. 20 seconds)
4.     Device will restart after around 2 minutes and is ready for use then

Inclusion XXXInclusionDescription
Exclusion XXXExclusionDescription
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Technical Data

Dimensions 0.1090000x0.0165000x0.1090000 mm
Weight 138 gr
Hardware Platform SD3503
EAN 4251295700823
IP Class IP 20
Voltage 5 V
Load 1 A
Battery Type 1 * BL-5C 3,7 V 1150 mAh
Device Type Z-Wave Controller
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeZ-Wave Controller