Quickstart

This is a Secure Barrier Add-On for XXXQFrequencyName. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:
Turn the primary controller of Z-Wave network into inclusion mode, short press the products Z-Wave button that you can find on the product's housing.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from Z-Wave Alliance Product data and may be incomplete. Please refer to the Manufacturers Manual for more information.

Product Description

Aeon Labs Garage Door Controller is a smart and wireless Garage Door Control system, you can control the garage door to open, close, or stop moving via wireless signal on your gateway client or phone application.The Garage Door Controller allows you to configure different alarm sounds to indicate the doors action. Each action alarm sound can be customized. To change or update new alarm sounds for the Garage Door Controller, connect the Garage Door Controller to your PC host with a USB cable and download your sound files to the flash memory (128 MB) of the Garage Door Controller.It can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. It is also a security Z-Wave device and supports the Over The Air (OTA) feature for the products firmware upgrade.

Reset to factory default Press and hold the Z-Wave button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is missing or inoperable.
Inclusion Turn the primary controller of Z-Wave network into inclusion mode, short press the products Z-Wave button that you can find on the product's housing.
Exclusion Turn the primary controller of Z-Wave network into exclusion mode, short press the products Z-Wave button that you can find on the product's housing.
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 Group 1 is assigned to the Lifeline association group and every device has 5 nodes to associate.When the Garage Door controller is received the commands sent by controller to be turned on or off, the Garage Door controller will send a basic report of its status to the nodes in association group 1. To change what kind of signal is sent to the nodes in group 1, please see the detailed description of configuration parameter 80.
2 5 When the Garage Door Controller receives the Basic Set, Switch Binary Set,commands from main controller. it will forward the Basic Set, Switch Binary Set to associated nodes in Group 2.

Configuration Parameters

Parameter 241: Pair the Sensor with Garage Door Controller

This parameter is used to pair the Sensor with Garage Door Controller.Note:1. This procedure should only be used when the complimentary Sensor is missing or inoperable and you have another new Sensor that would be paired with your Garage Door Controller.2. When the pairing is started, the Network LED will blink slowly, at this time, you just need to press the Temper Switch back of the Sensor once. If the Network LED change to be solid, which means the pairing is successful. Otherwise, repeat the steps.
Size: 4 Byte, Default Value: 0

Setting Description
1431655681 Start the Sensor pairing mode.

Parameter 252: Enable/Disable Lock Configuration

This parameter is used to enable/disable Lock all configuration parameters.(0 =disable, 1 = enable)
Size: 1 Byte, Default Value: 0

Setting Description
0 All configuration parameters are configurable.
1 All configuration parameters are not configurable (Locked).

Parameter 255: Reset to default factory setting

This parameter is used to reset product to default factory setting. (There are just 2 values can be used).
Size: 4 Byte, Default Value: 0

Setting Description
1 Reset all configuration parameters to default setting.
1431655765 Reset the product to default factory setting and be excluded from the Z-wave network.

Parameter 32: Configure the default startup ringtone.

This parameter is used to set the default startup ringtone for the Garage Door Controller.
Size: 1 Byte, Default Value: 2

Setting Description
0 Disable the startup ringtone.
1 - 100 Enable and select a startup ringtone for the Garage Door Controller.

Parameter 34: Calibration the Sensor.

This parameter is used to calibrate the Sensor.Calibration Steps:1. Let the garage door move to full close position. 2. Send this parameter (0x22) with value=1 to Garage Door Controller.3. Let the garage door move to full open position.4. Let the garage door move to full close position after the step 3 is completed.After the step 4 is completed, all calibration steps are complete.
Size: 1 Byte, Default Value: 0

Setting Description
1 Enable calibration.

Parameter 35: Set the timeout of Sensor calibration.

This parameter is used to set the timeout of Sensor calibration in parameter 34.The unit is second.
Size: 2 Byte, Default Value: 60

Setting Description
1 - 32767 Set the timeout of calibration

Parameter 36: Get the number of alarm music.

This parameter is used to get the the number of alarm music that are stored in the flash memory card.Note: this parameter only will use the configure get command to get the number of alarm music.
Size: 1 Byte, Default Value: 1

Setting Description
1 Get the number of alarm music.

Parameter 37: Configure the alarm mode when the garage door is opening.

This parameter is used to set an alarm mode when the garage door is opening..
Size: 4 Byte, Default Value: 524560

Setting Description
1 - 10 Configure the flash frequency of the alarm LED, there are 10 levels can be set.
16777215 Disable the alarm mode.
65535 - 65545 Configure the volume of alarm sound, there are 10 levels can be set.
256 - 356 Select an alarm sound, there are 4 alarm sounds in the flash memory card can be selected.
16777216 Enable the alarm mode.

Parameter 38: Configure the alarm mode when the garage door is closing.

This parameter is used to set the alarm mode when the garage door is closing.
Size: 4 Byte, Default Value: 524806

Setting Description
16777216 Enable the alarm mode.
1 - 10 Configure the flash frequency of the alarm LED, there are 10 levels can be set.
65535 - 65545 Configure the volume of alarm sound, there are 10 levels can be set.
16777215 Disable the alarm mode.
256 - 356 Select an alarm sound, there are 4 alarm sounds in the flash memory card can be selected.

Parameter 39: Configure the alarm mode when the garage door is in Unknown position.

This parameter is used to set the alarm mode when the garage door is in u0022Unknownu0022 position.
Size: 4 Byte, Default Value: 525060

Setting Description
1 - 10 Configure the flash frequency of the alarm LED, there are 10 levels can be set.
65535 - 65545 Configure the volume of alarm sound, there are 10 levels can be set.
16777215 Disable the alarm mode.
16777216 Enable the alarm mode.
256 - 356 Select an alarm sound, there are 4 alarm sounds in the flash memory card can be selected.

Parameter 40: Configure the alarm mode when the garage door is in closed position.

This parameter is used to set the alarm mode when the garage door is in closed position.
Size: 4 Byte, Default Value: 525314

Setting Description
16777216 Enable the alarm mode.
1 - 10 Configure the flash frequency of the alarm LED, there are 10 levels can be set.
256 - 356 Select an alarm sound, there are 4 alarm sounds in the flash memory card can be selected.
65535 - 65545 Configure the volume of alarm sound, there are 10 levels can be set.
16777215 Disable the alarm mode.

Parameter 41: Configuration report for the tamper switch State

This parameter is used to report the state when the Sensor is installed on the garage door or removed from the garage door.Note:The state would be reported via configuration report CC.
Size: 1 Byte, Default Value: 0

Setting Description
0 The Sensor is installed on the garage door.
15 The Sensor is removed from the garage door.

Parameter 42: Configuration report for the battery state of Sensor

This parameter is used to report the battery state of Sensor. Note:The state would be reported via configuration report CC.
Size: 1 Byte, Default Value: 0

Setting Description
15 Battery is in low battery state.
0 Battery is in normal state.

Parameter 43: Start playing or Stop playing the ringtone.

This parameter is used to audition or test the product's ringtone.
Size: 1 Byte, Default Value: 0

Setting Description
-1 Stop playing the ringtone.
1 - 100 Start playing the ringtone that you select.

Parameter 44: Test the volume of the current ringtone

This parameter is used to audition or test the product's ringtone volume.
Size: 1 Byte, Default Value: 0

Setting Description
1 - 10 There are 10 volume levelscan be set for testing.

Parameter 45: Get the environment temperature

This parameter is used to get the temperature where near to your Garage Door Controller.
Size: 2 Byte, Default Value: 0

Setting Description
0 - 500 The available temperature range is 0 to 50 Celsius

Parameter 47: Define the function of Button- and Button+.

This parameter is used to define the function of Button- and Button+.
Size: 1 Byte, Default Value: 0

Setting Description
1 Pressing it once, the Button+ and Button- are defined to be the control item of Next and Previous. Press and hold it, the Button+ and Button- are defined to be used to increase and decrease the volume.
0 Pressing it once, the Button+ and Button- are defined to be used to increase and decrease the volume. Press and hold it, the Button+ and Button- are defined to be the control item of Next and Previous.

Parameter 80: Enable/Disable to send notifications to associated devices to associated devices.

This parameter is used to enable/disable to send notifications to associated devices (in Group 1) when the state of Doorbell Gen5s load is changed. (0=Send nothing, 1=Send hail CC, 2=Send barrier operator report CC).
Size: 1 Byte, Default Value: 2

Setting Description
2 Send BARRIER OPERATOR Report Command
0 Send Nothing (Disabled)
1 Send HAIL Command

Technical Data

Hardware Platform ZM5101
Device Type Secure Barrier Add-On
Network Operation Always On Slave
Firmware Version HW: 62 FW: 1.11
Z-Wave Version 6.51.06
Certification ID ZC10-15090011
Z-Wave Product Id 0x0086.0x0203.0x003E
Frequency XXfrequency
Maximum transmission power XXantenna
Australia / New ZealandSecure Barrier Add-On