This is a
* Keyfob should not include any node * Under Control Mode: Press button 1 and 4 together till the red LED flashes to include into other Z-Wave network.* Under Setup Mode: Press button 3 and 4 together till the red LED flashes to include into other Z-Wave network.It will send NWI NIF info. * Keyfob will return to sleep after 5 seconds if no inclusion nor exclusion.
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Portable Controller with Remote Control Keyfob:* Micro USB Charge (5V)* Lithium Rechargeable Battery (280mAH)* Setting Mode (Inclusion/Exclusion/Association/Learning/Shift)* Control Mode (Arm/Disarm, On/Off Control)
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
Press 4 buttons together for 10 seconds. The LED colors will turn red after 2 seconds for 2 seconds and turn green for another 2 seconds. Keyfob will send Device Reset Locally Notification command and reset to the factory default. (Red LED flashes fast means reset completely).Remark: This is to be used only in the case of primary controller being inoperable or otherwise unavailable.
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Here are a few hints for network installation if things dont work as expected.
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Z-Wave Plus Lifeline |
As long as this device is not included into a Z-Wave network of a different controller it is able to manage its own Z-Wave network as primary controller. As a primary controller the device can include and exclude other devices in its own network, manage associations, and reorganize the network in case of problems. The following controller functions are supported:
Communication between two Z-Wave devices only works if both belong to the same wireless network. Joining a network is called inclusion and is initiated by a controller. The controller needs to be turned into the inclusion mode. Once in this inclusion mode the other device needs to confirm the inclusion - typically by pressing a button.
If current primary controller in your network is in special SIS mode this and any other secondary controller can also include and exclude devices.
To become primary a contoller have to be resetted and then include a device.
To Include into (adding into) an existing network: Put the Z-Wave Gateway or Controller into learn mode to add the keyfob into your controller. To get in to inclusion mode, the distance between sensor and controller is suggested to be within one meter.
The primary controller can exclude devices from the Z-Wave network. During exclusion the relationship between the device and the network of this controller is terminated. No communication between the device and other devices still in the network can happen after a successful exclusion. The controller needs to be turned into the exclusion mode. Once in this exclusion mode the other device needs to confirm the exclusion - typically by pressing a button.
Attention: Removing a device from the network means that it is turned back into factory default status. This process can also exclude devices from it's previous network.
To Exclude from (removing from) an existing network: Put the Z-Wave Gateway or Controller into learn mode to remove the keyfob into/from your controller. To get in to exclusion mode, the distance between sensor and controller is suggested to be within one meter.
Hardware Platform | ZM5101 |
Device Type | Remote Control - Simple |
Network Operation | Portable Controller |
Firmware Version | 02 |
Z-Wave Version | 6.51.06 |
Certification ID | ZC10-15060003 |
Z-Wave Product Id | 0x0109.0x201B.0x1B02 |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |