Z-Wave Europe
Z-Wave.Me Dimmer Set for Busch-Jaeger DURO 2000
SKU: ZMR_FMDM
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
This wall dimmer bundle is intended to control lamps, both with resistive or inductive load. The product consists of:
&bull the insert, which can be used with or without local control (equals ZME_06433)
&bull a special mounting plate to moount the insert into a pattress box
&bull a mounting frame in Busch Jager Duro 2000 series , color standard white
&bull the switching paddle for local control of the dimmer
The unit is designed for use within a 2-wire system, which means that no neutral wire (blue) is needed for operations. It will be included and controlled in a Z-Wave network from a remote control, a wireless control centre or any other kind of Z-Wave controller including a PC-software. The device is a conventional leading-edge phase control dimmer with support for inductive loads such as transformers. Additionally conventional resistive loads such as incandescent lamps or 230 V halogen lamps can be dimmed as well.
Technical Data:
- Power rating: 230V, 50 Hz
- Wiring: 2-wire-system
- Maximum loads:
- Incandescent lamps: 40...300W
- 230V (HV) halogen: 40...300W
- Low voltage halogen with standard transformer (inductive load): 30...300VA
- Low voltage halogen with switched power supply (reactive load): no
- Fluorescent light: 30…300VA, only dimmable lamps
- Wireless behaviour: receiver
- Z-Wave type: slave
- Installation: in pattress box
- Distance: up to 30 m in buildings
- Display: Multicolour-LED
- Interaction: two buttons to be completed with switching paddle for local operation
- Power supply: via 230 V power
- Dimensions: 48mmx48mmx23mm
The Z-Wave.Me dimming Flush-Mountable consists of standard DUWI Z-Wave hardware but located with an enhanced Z-Wave.Me firmware. The insert has two buttons.
Compared to the standard Duwi firmware this product offers a series of important enhancements:
- Works well within networks controlled by an IP gateway
- status changes are reported back to IP gateway in real time
- switching paddles can be used to control scenes in gateway
- Implements the most recent advancements of Z-Wave technology Explorer Frame for network wide inclusion and automated reconfiguration of networks
- Improved routing algorithm for faster communication
- Prevention against „Ghost Nodes“ after controller reset
Further enhanced features include
- Configurable night light
- Three association groups (single click, double click, status change)
- Switching paddle can be used for control independently of local operations
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| Dimensions | 0.0000000x0.0000000x0.0000000 mm |
| Weight | 70 gr |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.