Quickstart

This is a secure Z-Wave Device for XXXQFrequencyName. To run this device please connect it to your mains power supply. Here are a few steps to start building your own Smart Home devices based on Z-Uno. First of all, you need to install the Z-Uno software environment on your computer. The Arduino IDE is used to upgrade and program your Z-Uno. Windows users must install the Z-Uno driver for Windows. Once this is done, you can download examples provided by Z-Wave.me. (All examples are also available from the Arduino IDE via File - Examples - Z-Uno), you can modify them or write your own code. For more information on syntax, please visit the language reference.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

Z-Uno is the first and only easy-to-use developer board that allows you to create your own Z-Wave devices without in-depth knowledge of the Z-Wave protocol or programming. Z-Uno is a mix of Z-Wave home automation protocol strength and Arduino simplicity. Inspired by the Arduino project, Z-Uno inherits all concepts of easy to use hardware and software solutions to keep a maximum of flexibility. Z-Uno is a complete DIY product. It is made for those who are limited in their choice of existing Z-Wave products but want to expand their smart homes with more sensors and actuators. (LEDs connect, buttons, switches, motors, or any low voltage sensors, including most Arduino compatible sensors. Z-Uno programming is written as a sketch in simplified C and then loaded onto the Z-Uno using the Arduino IDE. Many examples and comprehensive tutorials will help you to make your own project. As a Z-Wave Plus certified device, Z-Uno is the perfect partner for your RaZBerry gateway. Z-Uno is also compatible with other controllers.

Installation

To install the device, either use the short information at the top of the page or go to the complete starting instructions on the website.

If you encounter problems, you can look at the Troubleshooting page.

Product Usage

Hardware Specification

  • 28 kB flash memory
  • 2 kB RAM 
  • Z-Wave RF transmitter at 9.6/40/100 kbps
  • 26 GPIO (shared with special outputs)
  • 4 ADC
  • 5 PWM
  • 2 UART
  • 1 USB (serial port)
  • 64 kB EEPROM
  • 1 SPI (master or slave)
  • 4 IR controllers, 1 IR learn capability
  • 1 TRIAC/ZEROX to control dimmer
  • 1 Interrupt
  • 2 Timers 16 MHz or external source
  • I2C (software)
  • 1-wire (software)
  • 8x6 Keypad Scanner
  • 2 service LED, 1 service button
  • 1 user test LED

Power supply:

  • USB 5 V, external 5 or 3 V, external 7-18 V or battery (via MU-2F connector, included)
  • always on, sleeping or FLiRS (Frequently Listening)


Here you can find more technical data.

Reset to factory default Press the key for five seconds, then press the key again three times
Inclusion

To include Z-Uno in a Z-Wave network, you must set the controller to Include mode (also known as Add mode). On the Z-Uno board the service button must be pressed three times. Z-Uno is now added to the Z-Wave network

 
Exclusion If your Z-Uno was already included in another network or you want to reset it to the factory settings, follow the Exclusion process: Start the Exclusion mode on your Z-Wave controller and press the service button on the Z-Uno three times
NIF Press the service button on the device three times. Z-Uno will send a Node Information Frame (NIF) to all devices in the area
Wakeup To wake up your sleeping Z-Uno, press the service button on the unit three times. Z-Uno will send a Node Information Frame (NIF) to all devices in the vicinity. Z-Uno will wake up periodically - depending on configuration - to inform the Z-Wave controller and wait for configuration from the controller.
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 Lifeline
2 5 Control Group

Technical Data

Dimensions 0.0205500x0.0140000x0.0395800 mm
Weight 6.81 gr
Hardware Platform ZM5101
EAN 4251295700984
Firmware Version 00.46
Z-Wave Version 4.05
Certification ID ZC10-16065104
Z-Wave Product Id 0x0115.0x0110.0x0001
Frequency XXfrequency
Maximum transmission power XXantenna
USZ-Wave Device