Quickstart

This is a secure HVAC-Thermostat for . Please make sure the internal battery is fully charged.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

Heatit Z-Temp2 is a battery-operated thermostat designed for usewith water based heating systems. Used in combination with theHeatit Z-Water regulator you can control your heating system with aZ-Wave primary controller/gateway with the use of Heatit Z-Water incombination with one or several Heatit Z-Temp2.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

  1. Make sure a device is in factory reset state before including. In doubt exclude before include.
  2. If inclusion still fails, check if both devices use the same frequency.
  3. Remove all dead devices from associations. Otherwise you will see severe delays.
  4. Never use sleeping battery devices without a central controller.
  5. Dont poll FLIRS devices.
  6. Make sure to have enough mains powered device to benefit from the meshing

Association - one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.

Association Groups:

Group Number Maximum Nodes Description
1 5 Lifeline. Normally used by the Z-WaveController.
2 5 Multilevel Sensor Report (internal measured temperate and measured relative humidity).
3 5 Binary Switch Set (normally used to control external relays).

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.

IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.

Parameter 1: Temperature/ Humidity report interval

Used to adjust the time between report interval for Temperature and humidity reports.
Size: 2 Byte, Default Value: 900

Setting Description
30 - 32767 30 to 32 767 seconds (Default 900)

Parameter 10: Temperature Control Hysteresis

Adjust the delta values for the thermostat to turn on off heating.
Size: 2 Byte, Default Value: 5

Setting Description
3 - 30 0.3 to 3C (Default 5, 0,5C)

Parameter 11: Minimum Temperature Limit

Set the minimum temperature limit.
Size: 2 Byte, Default Value: 50

Setting Description
50 - 400 5 to 40C (Default 50, 5C)

Parameter 12: Maximum Temperature Limit

Set the maximum temperature limit.
Size: 2 Byte, Default Value: 400

Setting Description
50 - 400 5 to 40C (Default 400, 40C)

Parameter 13: External Relay & Operating State update interva

Set time on how often the devices sends Binary Switch Set and thermostat mode to gateway.
Size: 2 Byte, Default Value: 0

Setting Description
0 Sends only when changed (Default)
1 - 240 1 to 240 minutes + When changed

Parameter 14: Report when presence is detected

Decides if the thermostat sends temperature when presence is detected.
Size: 2 Byte, Default Value: 0

Setting Description
0 Do not report to gateway when presence is detected, only at interval. (Default)
1 Send temperature report to gateway when presence is detected.

Parameter 2: Temperature delta value

Temperature delta value.
Size: 2 Byte, Default Value: 10

Setting Description
0 Reporting temperate based on change is disabled
5 - 50 0.5 to 5C (Default 10, 1.0C)

Parameter 3: Humidity delta value

Humidity delta value.
Size: 2 Byte, Default Value: 10

Setting Description
0 Reporting temperate based on change is disabled
5 - 50 5 to 50% (Default 10, 10%)

Parameter 4: Temperature offset settings

Calibrate the internal sensor.
Size: 2 Byte, Default Value: 0

Setting Description
-100 - 100 -100 to 100C (Default 0, 0C)

Parameter 5: Humidity offset settings

Offsets the measured relative humidity.
Size: 2 Byte, Default Value: 0

Setting Description
-100 - 100 -10 to 10% (Default 0, 0%)

Parameter 6: Proximity sensor retrigger interval

Proximity sensor retrigger interval.
Size: 2 Byte, Default Value: 10

Setting Description
2 - 270 2 to 270 seconds (Default 10, 10 seconds)

Parameter 7: Proximity sensorEnable / Disable

Choose if proximity sensor is used or not.
Size: 2 Byte, Default Value: 1

Setting Description
0 Disable
1 Enable (Default)

Parameter 8: LED maximum brightness

Adjust the backlight of LCD display.
Size: 2 Byte, Default Value: 50

Setting Description
0 - 99 0 to 99% (Default 50, 50%)

Parameter 9: LED turned on before timeout

Adjust the time from proximity sensor / display touched until display goes to sleep.
Size: 2 Byte, Default Value: 3

Setting Description
3 - 300 3 to 300 secounds (Default 3, 3 seconds).

Technical Data

Hardware Platform EFR32Z
Device Type Thermostat - HVAC
Network Operation Listening Sleeping Slave
Firmware Version HW: 1 FW: 1.01:00.02
Z-Wave Version 7.11.1
Certification ID ZC12-20050065
Z-Wave Product Id 0x019B.0x0004.0x0204
Firmware Updatable Updatable by Manufacturer
Thermostat HVAC Systems Supported Dual FuelHumidity ControlUniversal
Color White
Thermostat Modes Heat
Thermostat Power Source Battery
Security V2 S2_UNAUTHENTICATED ,S2_AUTHENTICATED
Frequency XXfrequency
Maximum transmission power XXantenna

Supported Command Classes

  • Application Status
  • Association Grp Info V3
  • Association V2
  • Basic V2
  • Battery
  • Configuration V4
  • Device Reset Locally
  • Firmware Update Md V5
  • Indicator V3
  • Manufacturer Specific V2
  • Multi Channel Association V3
  • Notification V8
  • Powerlevel
  • Protection
  • Security
  • Security 2
  • Sensor Multilevel V5
  • Supervision
  • Thermostat Mode V3
  • Thermostat Operating State
  • Thermostat Setpoint V3
  • Transport Service V2
  • Version V3
  • Zwaveplus Info V2

Explanation of Z-Wave specific terms

  • Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
  • Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
  • Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
  • Inclusion — is the process of adding new Z-Wave devices into a network.
  • Exclusion — is the process of removing Z-Wave devices from the network.
  • Association — is a control relationship between a controlling device and a controlled device.
  • Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
  • Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.