Quickstart
This is a
Z-Wave Device
for
.
To run this device please connect it to your mains power supply.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law.
The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material.
Use this equipment only for its intended purpose. Follow the disposal instructions.
Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This
device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way
communication) and every mains powered node can act as a repeater for other nodes
(meshed network) in case the receiver is not in direct wireless range of the
transmitter.
This device and every other certified Z-Wave device can be used together with any other
certified Z-Wave device regardless of brand and origin as long as both are suited for the
same frequency range.
If a device supports secure communication it will communicate with other devices
secure as long as this device provides the same or a higher level of security.
Otherwise it will automatically turn into a lower level of security to maintain
backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer
to www.z-wave.info.
Product Description
Always feel safe knowing your home is protected, inside and out.
The new Yale Smart Alarm Starter Kit is a perfect solution for homeowners who demand top-of-the-line security and unparalleled convenience. Easy to set up and use, the Smart Alarm is sleekly designed, elegant, and highly functional, to seamlessly blend into any home. The Yale Smart Alarm is fully controllable using the Yale Home app, which gives you security, convenience, and peace of mind at the touch of a button! The Yale Smart Alarm works seamlessly with other Yale smart products and leading voice assistants for a completely customizable security experience.
App control: Real-time monitoring with push notifications when the alarm sensors are triggered, as well as the ability to arm/disarm your alarm from anywhere in the world.
Fully customizable: Set up and control up to four individually configured areas around your property and add additional accessories to suit your needs.
Horizon+ Technology: Larger range of protection of up to 1km, and increased battery life, allowing you to protect homes, properties or attached buildings of all shapes and sizes.
Features:
- Multi-house support: Secure multiple properties from a single app.
- Perimeter security: detect and prevent any potential incidents before they occur thanks to a range of additional outdoor accessories.
- Shared access: Grant control to your Smart Alarm to people you trust.
- Geofencing: Get a reminder to arm your alarm as you leave home.
- Supports Wi-Fi, Ethernet, Bluetooth and Cellular Backup (4G LTE)* (*Requires subscription plan.)
- Advanced services through a subscription plan: Cellular Backup Communication, Automated Call Alert and Professional Monitoring.
- Scope of Delivery: 1x Yale Smart Alarm Hub, 1x Yale Indoor Motion Detector, 1x Indoor Window Door Sensor, 1x Keypad, 1x Keyfob, 4x Battery, 4x Screws and Adhesive Pad for Mounting, 1x Power Supply, 1x Quick Start Guide
Features:
- Wireless Range: Horizon+ Technology: 1km long range RF
- Communication frequency between Yale Hub and alarm devices: Horizon+ Technology: 2-way RF on 868Mhz
- Model number: AL-ESTARTKIT1-1A-V1 / AL-SK1-1A-EU
In the box:
1 x Yale Smart Alarm Hub
- Up to 4 security areas, Connect up to 100 alarm devices, 100db siren and speaker
- Product Dimensions (HxWxD): 175mm x 175mm x 35.8mm
- Product Weight: 410g
- Power Solution: Power via AC Adapter (included)
- Battery Lifetime: Battery Back-Up: Up to 12 hours fully functional
- Mounting Solution: Table or Wall mount (wall mounting plate and screws included)
1 x Yale Indoor Window Door Sensor
- Detects open/closing of window/door
- Product Dimensions (HxWxD): 68.5mm x29mm x 9.52mm
- Product Weight: 35g
- Power Solution: 1x CR2045 lithium battery
- Battery Lifetime: Up to 4 years
- Mounting Solution: Screws and 3M tape (included)
1 x Yale Indoor Motion Sensor
- Selectable pet immunity, Selectable sensitivity, 12m detection range
- Product Dimensions (HxWxD): 121.75mmx 71.75mm x 55mm
- Product Weight: 110g
- Power Solution: 1x CR123A lithium battery
- Battery Lifetime: Up to 3 years
- Mounting Solution: Screws and 3M tape (included)
1 x Yale Keypad
- Fully-arm (Away arming), disarm or part-arm (Home arming), Area selection, Panic function, Automatic backlight lights up when approaching keypad
- Product Dimensions (HxWxD): 122mm x 64mm x 22.49mm
- Product Weight: 115g
- Power Solution: 1x CR123A lithium battery
- Battery Lifetime: Up to 3 years
- Mounting Solution: Table or Wall mount (wall mounting plate included)
1 x Yale Keyfob
- Fully-arm (Away arming), disarm or part-arm (Home arming), Keylock (to prevent keys being accidentally pressed), Panic function, LED feedback
- Product Dimensions (HxWxD): 106mm x 36mmx 12mm
- Product Weight: 30g
- Power Solution: 1x CR123A lithium battery
- Battery Lifetime: Up to 3 years
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default
state. Please make sure to reset the device into factory default. You can do this by
performing an Exclusion operation as described below in the manual. Every Z-Wave
controller is able to perform this operation however it is recommended to use the primary
controller of the previous network to make sure the very device is excluded properly
from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific
installation guidelines/norms may do works with mains power. Prior to the assembly of
the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs
to be added to an existing wireless network to communicate with the devices of this network.
This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion.
Both processes are initiated by the primary controller of the Z-Wave network. This
controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is
then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
Dimensions |
0.1750000x0.1750000x0.0300000 mm |
Weight |
870 gr |
EAN |
5052847131190 |
Frequency |
XXfrequency |
Maximum transmission power |
XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network.
Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network.
Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be
a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and
a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave
device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a
Z-Wave device to announce its capabilities and functions.