Quickstart

This is a Binary Sensor for XXXQFrequencyName. To run this device please insert fresh 2 * AAA batteries. To run this device please make sure the internal battery is fully charged.

After removing the cover push the tamper switch for three seconds until the red LED blinks. Inclusion and Exclusion is confirm when the tamper switch is released at this moment. The same process sends out a NIF. Removing the cover wakes up the device.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

This battery operated device combines a temperature sensor with a binary sensor using dry input connectors. Both sensor functions can be used independently. The device has a tampering protection switch that is suited for applications where the dry inputs are used for security related application. The binary sensor is issuing a wireless command whenever the connection is closed or opened. The temperature sensor needs to be polled in order to get its value. The device is IP 20 rated and can be used in dry environments only. The precision of the temperature sensor is in the range of +/- 1 °C

Attention: This is a multi purpose device with the binary sensor as primary and the temperature as secondary function. Depending on the policies used certain simplistic User Interfaces - such as VERA Dashboard - may not show the temperature value but the dry input as binary sensor only.

Installation

Please make sure to insert the batteries in the right direction. Don"t mix batteries of different type or vendor. The device can be mounted on every flat and dry surface either using double sided adhesive tape or any type of screws.

Product Usage

The device can be mounted in every location of a room for measuring the temperature. For optimal values it is recommended to mount the sensor at a wall in a hight of 1,50 m above the ground and not directly to a heater.

the binary sensor can be used as a door or window sensor. Therefore you can use a simple two-wire cable.

Reset to factory default XXXResetDescription
Inclusion

After removing the cover push the tamper switch for three seconds until the red LED blinks. Inclusion and Exclusion is confirm when the tamper switch is released at this moment.

Exclusion

After removing the cover push the tamper switch for three seconds until the red LED blinks. Inclusion and Exclusion is confirm when the tamper switch is released at this moment.

NIF

After removing the cover push the tamperswitch for three seconds until the red LED blinks. Releasing the tamper switch issues a Node Information Frame.

Wakeup

Removing the cover wakes up the device.

Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
2 5 Alarm triggered by Tamper Switch
1 5 Dry Binary Input close/open

Configuration Parameters

Parameter 1: Reset

Resets the device
Size: 1 Byte, Default Value: 00

Setting Description
00 normal operation
01 reset

Parameter 2: Command Sent on Dry Input

Defines the type of command sent when dry input triggers
Size: 1 Byte, Default Value: 00

Setting Description
00 Alarm Report Type 2
01 Basic On or Off

Parameter 5: Operation Mode

Defines ufffcif the sensor is in normal - ufffcwakeup- mode or always on. This ufffcfunction shall be used only for testing ufffcsince its draining the battery very fast
Size: 1 Byte, Default Value: 00

Setting Description
01 normal mode
03 always awake

Parameter 6: Temperature Offset

Allows to calibrate the temperature measurement function
Size: 1 Byte, Default Value: 00

Setting Description
00 0 K
ce - 32 Temperature Offset in K

Technical Data

Dimensions 0.0030000x0.0050000x0.0010000 mm
Weight 20 gr
Hardware Platform ZM3102
EAN 0696859123351
Battery Type 2 * AAA
Device Type Routing Binary Sensor
Generic Device Class Binary Sensor
Specific Device Class Binary Sensor
Firmware Version 00.27
Z-Wave Version 02.61
Certification ID ZC08-12120004
Z-Wave Product Id 0097.1182.4501
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeRouting Binary Sensor