ZLINK
Z-Wave In-Wall Dimmer
SKU: WD-100
Quickstart
This is a
Place your Z-Wave controller in "Inclusion" mode. Then tap either the top or bottom paddle once to initiation Inclusion.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
ZLINKs WD-100 is a Z-Wave Plus certified device with S2 security and SmartStart features. You can now add this device securely and with ease using QR code on the product with compatible gateways supporting S2 and Smart Start. The elegant WD-100, with 7 LED dim level lights, communicates with other Z-Wave certified devices and updates your home into a smart home. WD-100 replaces a standard in-wall light switch turning it into a Z-Wave controlled network device with manual and remote control dimming and On/Off light control. ZLINK WD-100 supports, Instant Feedback of manual status to compatible gateways as well as Central Scene to allow setting multiple scene control throughout the home, with gateways supporting Central Scene. Each Z-Wave device serves as a node to repeat the signal in the network, thus, extending the overall Z-Wave mesh wireless network range.Additional Features: Power 120 VAC, 60Hz, up to 600 watts Region US: 908.4, 916 MHz Works w/ most incandescent, dimmable CFL & LED lights 7 segment LED dim level indicator Remotely or manually turns ON or OFF, or DIM lights Fits standard wall plates (wall plate not included) Works with any certified gateway supporting Z-Wave
| Reset to factory default | 1. Turn the connected light ON with the rocker2. Quickly tap the topside of the rocker 3 times3. Then quickly tap the bottom side of the rocker 3 timesIf you see the lights turn OFF then ON it means that the module has been rest successfully.Please use this procedure only when the network primary controller is missing or otherwise inoperable. |
| Inclusion | Place your Z-Wave controller in "Inclusion" mode. Then tap either the top or bottom paddle once to initiation Inclusion. |
| Exclusion | Place your Z-Wave controller in "Exclusion" mode. Then tap either the top or bottom paddle once to initiation Exclusion. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | 1. Z-Wave Plus Lifeline2. Central Scene Notification3. Switch Multilevel Report4. Device Reset Locally Notification |
Configuration Parameters
Parameter 10: Timer for turning On or Off the lights manually
Timer for turning On or Off the lights manually.Parameter 10 indicates the time duration of each level when the light is controlled by paddle switch Size: 2 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 1 - 255 | Parameter 10 indicates the time duration of each level when the light is controlled by paddle switch |
Parameter 4: Orientation of ON/OFF on rocker switch
The orientation of the ON/OFF on the rocker switch can be inverted using parameter 4. If value =0, the connected light will turn ON by pressing the top side of the rocker switch and turn OFF by pressing the bottom side. If value =1 the connected light will turn OFF by pressing the top side of the rocker switch and turn ON by pressing the bottom side. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 1 | If value =0, the connected light will turn ON by pressing the top side of the rocker switch and turn OFF by pressing the bottom side. If value =1 the connected light will turn OFF by pressing the top side of the rocker switch and turn ON by pressing the bottom side. |
Parameter 7: Resolution Level of Dimming
Resolution level for turning On or Off the lights via remote control.Parameter 7 indicates the number of levels when the light is controlled by remote. Lower this number, the finer the control of dimming. Higher the number the faster the dimming will jump from one state to another. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 99 | Parameter 7 indicates the number of levels when the light is controlled by remote. Lower this number, the finer the control of dimming. Higher the number the faster the dimming will jump from one state to another. |
Parameter 8: Speed of Dimming
Parameter 8 is regarding the speed for turning On or Off the lights via remote control or scheduled program.Parameter 8indicates the time duration of each level when the light is controlled by remote. For example, if the Parameter 7 is set to 1 and Parameter 8 is set to 3, it will take approximately 3 seconds for the lights to turn On or Off when you remotely turn On or Off the switch. This provides a soft feel for the lights turning On or Off. If you prefer instant On or Off like incandescent light bulb, you can set a higher number for Parameter 7 and set parameter 8 to 1. Size: 2 Byte, Default Value: 3
| Setting | Description |
|---|---|
| 1 - 255 | Parameter 8indicates the time duration of each level when the light is controlled by remote. For example, if the Parameter 7 is set to 1 and Parameter 8 is set to 3, it will take approximately 3 seconds for the lights to turn On or Off when you remotely turn On or Off the switch. This provides a soft feel for the lights turning On or Off. If you prefer instant On or Off like incandescent light bulb, you can set a higher number for Parameter 7 and set parameter 8 to 1. |
Parameter 9: Level for turning On or Off the lights manually
Level for turning On or Off the lights manually.Parameter 9 indicates the number of levels when the light is controlled by paddle switch. Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 99 | Parameter 9 indicates the number of levels when the light is controlled by paddle switch. |
Technical Data
| Hardware Platform | ZM5202 |
| Device Type | Light Dimmer Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 255 FW: 50.03 |
| Z-Wave Version | 6.81.00 |
| Certification ID | ZC10-18025996 |
| Z-Wave Product Id | 0x0315.0x4447.0x3034 |
| Z-Wave Scene Type | Scene & Central Scene |
| Firmware Updatable | Updatable by Consumer by RF |
| Color | White |
| Electric Load Type | Dimmable FluorescentDimmable LEDFluorescentIncandescentLED |
| Switch Type | Decorator Paddle Rocker |
| Outdoor Use | ok |
| Neutral Wire Required | ok |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |