TESLA Smart Home
TESLA Smart Home Smart Switch Dual Zigbee
SKU: TSLZSWI-ZIGBEE2
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
The TESLA Smart Home Smart Switch Dual Zigbee will become your invaluable little helper. With its features and the Tesla Smart app, you can set it up to fit your smart home.
Zigbee Protocol.
The system that ensures that everything runs smoothly works with the ZigBee protocol. It is very stable, so your home will always be monitored.
TESLA Smart App.
You can keep an eye on your entire household via the TESLA Smart app, which you can download to your phone or tablet.
Voice Control.
The TESLA Smart app is compatible with Google Assistant and Amazon Alexa. This means that you can control your devices with your voice.
A system you can rely on.
ZigBee is a very stable and reliable technology that creates a common network between devices that allows them to communicate and even react to each other. This way, many tasks in your home can be performed automatically, taking away some of your worries.
Get smart lighting with the TESLA switch.
You can choose from a standard one-button version or the two-button TESLA Smart Switch Dual ZigBee, to which you connect two circuits of lights, which you then control separately.
No neutral needed.
The TESLA Smart Switch Dual ZigBee does without the neutral wire.
All in one place.
Control your entire smart home via the TESLA Smart app on your iOS or Android smartphone or tablet. The app is very clear, easy to use and available in English language.
Zigbee protocol.
The product belongs to a group that uses the ZigBee protocol by which the products communicate with each other. For the proper functioning of these products, it is necessary to have the TESLA Smart ZigBee Hub central unit as part of the smart home. This creates a common network for these products and allows them to interact with each other. For example, if the humidity sensor detects an increased value, it will automatically notify the dehumidifier via the TESLA Smart ZigBee Hub, which will start.
Features:
- Smart Switch Dual Zigbee
- ID: TSL-SWI-ZIGBEE2
- Maximum Load: Incandescent light bulb: 5–280 W (1 output)
- Rated Power: ?0.5 W (Power in standby mode)
- Power supply: 100?240 V AC 50/60 Hz
- Operating Temperature: -10?45 °C
- Operation Humidity Range: < 90 %
- Dimensions: 86 x 86 x 37,5 mm
- Connectivity: Zigbee
- App TESLA Smart: Google Android 6.0+, Apple iOS 11.0+
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| Dimensions | 0.0860000x0.0860000x0.0375000 mm |
| Weight | 116 gr |
| EAN | 8596115815063 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.