TESLA Smart Home

TESLA Smart Home Smart Dimmer Wi-Fi

SKU: TSLZSWI-DIMMER

Quickstart

This is a Z-Wave Device for . To run this device please connect it to your mains power supply.

Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

Too much light in the living room for watching TV and not enough for reading? With the TESLA Smart Home Smart Dimmer Wi-Fi, you can adjust the light intensity to your needs without always going to the switch. You can connect it to any dimmable light bulb and all you need to control it is your smartphone.

Automated Functions.
You can set it up exactly to your liking. The dimmer will react precisely as you wish, brightening or dimming the lights.

One App For Everything.
Just slightly move your finger. That"s all you need to do to control the lights of your entire smart home.

Control Via Wi-Fi.
No additional device is needed to control the dimmer. A standard Wi-Fi connection and your smartphone will do.

Set it up from the comfort of your couch.
You don"t even have to get off the couch to dim or turn off the lights. The dimmer has a built-in Wi-Fi module so you can control it via the TESLA Smart app, which is available in English language for both Android and iOS. If you prefer manual control, you can adjust the light intensity directly on the panel of the device.

Get comfortable thanks to automated functions.
With the TESLA Smart Dimmer, you can adjust the lights to suit the time of day and your schedule. For instance, you can set your lights to automatically turn on only in dimmed mode at night so they don"t blind you when you go to the kitchen or bathroom at night.

A smart, easy-to-use dimmer.
So you can adjust the intensity manually with the rotary switch.

Mechanical switch.
In addition to remote control via the app, the TESLA Smart Dimmer is equipped with mechanical switches.

The dimmer gets along with Google Assistant and Alexa.
The TESLA Smart Dimmer also fits perfectly into your smart home as it is compatible with both Google Assistant and Amazon Alexa. Simply connect it to all the other smart gadgets in your home and control them all from one place.

Features:

Smart Switch Dimmer Wi-Fi
ID: TSL-SWI-DIMMER
Maximum Load: Incandescent light bulb: 300 W, Fluorescent lamp (CFL): 220 W, LED: 220 W
Dimming Control: Trailing edge
Number of Controlled Outputs: 1 output
Rated Power: ?0.5 W (Power in standby mode)
Power Supply: 100?240 V AC 50/60 Hz
Operating Temperature: -10?45 °C
Operation Humidity Range: < 90 %
Dimensions: 86 x 86 x 53,5 mm
Connectivity: Wi-Fi 2.4 GHz IEEE 802.11b/g/n
App TESLA Smart: Google Android 6.0+, Apple iOS 11.0+

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

Make sure a device is in factory reset state before including. In doubt exclude before include.
If inclusion still fails, check if both devices use the same frequency.
Remove all dead devices from associations. Otherwise you will see severe delays.
Never use sleeping battery devices without a central controller.
Dont poll FLIRS devices.
Make sure to have enough mains powered device to benefit from the meshing

Technical Data

Dimensions	0.0860000x0.0860000x0.0535000 mm
Weight	126 gr
EAN	8596115815018
Frequency	XXfrequency
Maximum transmission power	XXantenna

Explanation of Z-Wave specific terms

Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
Inclusion — is the process of adding new Z-Wave devices into a network.
Exclusion — is the process of removing Z-Wave devices from the network.
Association — is a control relationship between a controlling device and a controlled device.
Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.