TESLA Smart Home
TESLA Smart Home Smart Water Sensor Zigbee
SKU: TSLZSEN-WATER
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
A burst pipe, poor quality seals or an overflowing bathtub? All of these can turn your house into a paddling pool. However, with a water leak sensor TESLA Smart Sensor Water, you"ll be able to react in time to prevent the worst damage in these situations.
Long Life.
All TESLA sensors are very energy-efficient. The Tesla Smart Water sensor can operate up to two years on a single battery.
Quality Range.
With ZigBee, you are guaranteed a signal range of up to 50 m. So you can rest assured that every part of your house is secured.
A Perfect Overview.
The sensor TESLA Smart Sensor Water constantly communicates with the smart app on your phone or tablet. It keeps you updated on what"s going on at home.
You won"t even notice it.
The TESLA Smart Sensor Water is fully wireless and powered by a single battery. Due to very efficient energy-saving mode, the battery life is really long. The sensor also automatically asks you to replace the battery once it runs out. Thanks to its great design and high reliability, it fits perfectly into any interior and will never let you down.
Set it up as you please.
A smart home in which the water leak sensor uses the ZigBee protocol. This system connects all features of the smart home and allows them to communicate with each other. You then choose how exactly you want to use the sensor. You can choose from several variable modes which can then be adapted to different scenarios.
Long life.
All TESLA sensors are very energy-efficient. The TESLA Smart Water sensor can operate up to two years on a single battery.
It gets along with smart assistants.
The TESLA Smart ZigBee Hub pairs the sensor with the TESLA Smart app, which is compatible with iOS and Android mobile operating systems. You can then set the device in the app. The TESLA Smart app also gets along great with smart personal assistants Google Assistant and Amazon Alexa.
With sensors, you won"t miss a thing.
The ZigBee protocol is very stable, so you don"t have to worry about any failures or malfunctions of devices that use this technology. The water leak detection sensor will always be ready to notify you immediately if it detects a flood.
Zigbee protocol.
The product belongs to a group that uses the ZigBee protocol by which the products communicate with each other. For the proper functioning of these products, it is necessary to have the TESLA Smart ZigBee Hub central unit as part of the smart home. This creates a common network for these products and allows them to interact with each other. For example, if the humidity sensor detects an increased value, it will automatically notify the dehumidifier via the TESLA Smart ZigBee Hub, which will start.
Features:
- Smart Water Sensor Zigbee
- ID: TSL-SEN-WATER
- EAN: 8596115811089
- Low Battery Notification: Yes
- Power Supply: 1x button cell CR2032
- Operating Temperature: 0?55 °C
- Dimensions: Ø50 x 18 mm
- Connectivity: Zigbee
- App TESLA Smart: Google Android 6.0+, Apple iOS 11.0+
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| Dimensions | 0.0500000x0.0500000x0.0180000 mm |
| Weight | 23 gr |
| EAN | 8596115811089 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.