TESLA Smart Home
TESLA Smart Home Smart Switch Module Dual Wi-Fi
SKU: TSLLSWI-WBREAK2
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
What if you want smart lighting in your home, but don"t feel like replacing your original switches? The TESLA Smart Switch Module Dual is the perfect solution. It turns any standard switch into a smart one.
Wi-Fi Connection.
No additional device is needed to control the dimmer. A standard Wi-Fi connection and your smartphone will do.
Voice Control.
After connecting the product with smart devices, you can also control the device with your voice. This makes the use of your smart device even easier.
Control As You Wish.
The app that you download to your smartphone allows you to either set up specific scenarios or control the devices remotely.
A hidden helper for every interior.
The advantage of the smart relay TESLA Smart Switch Module Dual is that it connects under a standard switch to an installation box in the wall. You get all the benefits of smart lighting without having to give up your original switches which you don"t want to lose because they, for instance, fit in perfectly with the rest of the interior.
Control via an app or automate directly.
The TESLA Smart app, that is available for iOS and Android in English language, puts lighting under your thumb. Pair the app with the switch and control the lighting remotely. Or create scenarios in the app and the lights will turn off or on automatically.
Google Assistant and Amazon Alexa.
You can control it with your voice or connect it to other smart assistants.
It gets along with smart assistants.
If you"re a fan of smart home gadgets, the TESLA Smart Swith Module Dual is sure to fit right in.
Expand your smart home with the TESLA smart relay.
With the TESLA Smart Switch Module Dual, you can control two circuits separately. You will find this useful in the bedroom, for instance, where you can connect one to the main light in the room and the other to the bedside light.
Features:
- Smart Switch Module Dual Wi-Fi
- ID: TSL-SWI-WBREAK2
- Maximum Load: 5 A / 1200 W
- Number of Controlled Outputs: 2 output
- Rated Power: ?0.5 W (Power in standby mode)
- Power Supply: 100?240 V AC 50/60 Hz
- Operating Temperature: -10?45 °C
- Operation Humidity Range: < 90 %
- Dimensions: 48 x 48 x 18 mm
- Connectivity: Wi-Fi 2.4 GHz IEEE 802.11b/g/n, Bluetooth (pairing only)
- App TESLA Smart: Google Android 6.0+, Apple iOS 11.0+
- Management App: SmartLife or Tuya Smart App
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| Dimensions | 0.0480000x0.0480000x0.0180000 mm |
| Weight | 42 gr |
| EAN | 8596115815070 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.