This is a
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
A smart bulb fits perfectly into any smart home. Whether you need bright, white lights for work or dim, warm lights for a night out watching TV, smart bulbs will always adapt.
RGB Colour Combination.
Colour temperature ranges from 2,700K - 6,500K RGB. This means that the smart bulb offers you a wide range of colours to choose from.
Superior Performance.
The smart bulb has an electrical input of 11 W and boasts a luminous intensity of 1050 lumens. With these specs, this smart bulb is perfect for shining light into every corner of your home.
TESLA Smart App.
Download the TESLA Smart app to your iOS or Android smart device. Here you can easily set a wide range of parameters: the intensity of the light, the colour of the light or different modes to create the desired atmosphere.
Create the right atmosphere.
Colour temperature ranges from 2,700K - 6,500K RGB. The bulb thus offers a wide range of colours from which you can choose according to your taste and current needs. The bulb is also dimmable and allows you to adjust the white colour temperature. With options like these, you really will find the right light for every occasion!
Set your scenarios.
With smart bulbs, you"ll never have to hunt for the light switch when you get home. That"s because you can link them to a motion sensor, and the moment you walk in your smart home will light up without you having to move a hand. The lights can also be controlled from a remote control or from an app on your phone.
TechToy Smart Bulb RGB E27.
Voice control allows you to become the true ruler of your home.
Simplicity in every way.
Working with the smart bulb is very easy. The thread type of the bulb is E27, this is the most common thread type, so installation shouldn"t be complicated for you. In the app, you can control it very easily, which means not only more convenience, but also possible energy saving. For example, if you forget to turn off the lights when you leave in a hurry. The app makes it very easy to find out if your home is unnecessarily lit and turn off the lights remotely.
Features:
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Here are a few hints for network installation if things dont work as expected.
Dimensions | 0.0750000x0.0750000x0.1450000 mm |
Weight | 60 gr |
EAN | 8596115842014 |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |