This is a
Inclusion and Exklusion are confirmed by hitting the button one time.
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
The TKB TZ68 is a switch plug that can be placed between a schuko wall outlet and electric devices, plugged in by cord. It can switch all loads up to 3500 W. The device is IP 20 rated and can therefore only be used in dry environments. Switching is controlled wirelessly using Z-Wave or locally applying a button. A blue LED indicates the switching status.
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
The Switch Plug can be plugged into every wall outlet for Plug-Type F (Poland, France,...). It is IP20 rated and can therefore only be used in dry environments. Do not locate the device facing direct sunlight, humid or dusty place. The suitable ambient temperature for the device is 0°C ~ 40°C.
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
hit the button on the device.
hit the button on the device.
The device is able to dim electric load up to 3500 W. Short press of the button will toggle. This means that the power will be turned on if it was off and turned off when it was on.
Here are a few hints for network installation if things dont work as expected.
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Size: Byte, Default Value:
Setting | Description |
---|
Size: Byte, Default Value:
Setting | Description |
---|
Size: Byte, Default Value:
Setting | Description |
---|
Size: Byte, Default Value:
Setting | Description |
---|
Dimensions | 0.0600000x0.1020000x0.0750000 mm |
Weight | 127 gr |
Device Type | On/Off Power Switch |
Generic Device Class | Binary Switch |
Specific Device Class | Binary Power Switch |
Firmware Version | 01.04 |
Z-Wave Version | 03.28 |
Certification ID | ZC08-13070001 |
Z-Wave Product Id | 0118.0101.0103 |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |