Quickstart

This is a On/Off Power Switch for XXXQFrequencyName. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:
After mounting the UZB controller to your PC and running the PC Controller program, click the Add button in the PC Controller program. Press the button on the Smart Plug for more than five seconds after you plug the Smart Plug into a power outlet and it will include to the network controller, while flashing the red button on the LED Smart Plug.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from Z-Wave Alliance Product data and may be incomplete. Please refer to the Manufacturers Manual for more information.

Product Description

The device can remotely power on/off to the load connected and will inform you of the electricity usage of your load.You can use it to measure the power of the load connected to the device (currently instantaneous power & used power).

Reset to factory default Press the button on the Smart Plug for more than 10 seconds after you plug the Smart Plug into a power outlet will make a Exclusion in the network controller, while the flashing red button LED Smart Plug. And all the variables are initialized. Please use this procedure only in the event that the network primarycontroller is missing or otherwise inoperable
Inclusion After mounting the UZB controller to your PC and running the PC Controller program, click the Add button in the PC Controller program. Press the button on the Smart Plug for more than five seconds after you plug the Smart Plug into a power outlet and it will include to the network controller, while flashing the red button on the LED Smart Plug.
Exclusion After mounting the UZB controller to your PC and run the PC Controller program you can click the Remove button in the PC Controller program. Press the button on the Smart Plug for more than five seconds after you plug the Smart Plug into a power outlet will Exclusion in the network controller, while the flashing red button LED Smart Plug.
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 Z-Wave Plus Lifeline, see attatched manual.

Configuration Parameters

Parameter 1: Standy Power Setting Value

this parameter determines whether to use the standby power cutoff function and determines the reference value of standby power cut off. If ther power consumption is less than the reference value, switch is turned off.this parameter value's size is 4 bytes. first 3 bytes is for setting standby power reference value. last 1 byte is for standby power monitoring function enable or disable.- Standby power setting value : 3 Byte- Standby Power Enable/Disble : 1 Byte)standby power value example:if the value is set by 300(0x00012C), standby power is 3.00wstandby power function enable/disable example :If standby power is enable, value is 0x01. and, total 4 bytes is 0x00012C01, ( Default parameter value : 00.00W, StandbyPower Disable)(max standby reference power is 600W, 0x00EA60)
Size: 4 Byte, Default Value: 0

Setting Description
0 - 60000 standby power reference value range(3 byte)
0 - 1 standby power monitoring function enable/disable setting value

Parameter 2: Peridic Measurement Value Transmission

this parameter determines whether or not to periodically reports the measured power values.Value : 1 (transmits a power value measured at the plug, periodically.Value : 0 (not transmitting power value) ( Default :1)
Size: 1 Byte, Default Value: 1

Setting Description
0 - 1 If value is 0, Plug do not transmit power value. If value is 1, plug transmits power value to hub.

Parameter 3: Accumulation Start/Stop

this parameter is for the function measuring the power used cumulatively.Value : 0 - stop accumulatingpower value.Value : 1 - start accumulatingpower value.( Default : Accumulation Start )(This configuration value is used only 0 and 1.)
Size: 1 Byte, Default Value: 0

Setting Description
0 - 1 If value is 0, plug stop accumulating power value. If value is 1, plug start accumulating power value.

Parameter 4: Connected Device Use/Not Use

this parameter is a value that indicates whether the device is in use connected to the plug. this is read only. and this parameter has meaning only when the standby power off function is On. Value : 0 - when connected Device(home appliance) is Not UseValue : 1 - When connected Device(home appliance) is in Use- Before setting the standby power mode, this parameteris meaningless. Only when using Standby power break mode, plug can report this parameter.(This configuration value is used only 0 and 1.)
Size: 1 Byte, Default Value: 0

Setting Description
0 - 1 If value is 0, connected device is Not use, If value is 1, it is in use.

Parameter 5: Periodic Time Intervals

this parameter is for the periodic report interval. Minimum time interval : 10minutes(standard unit)Value : 1 (10minutes * 1) = 10minutes intervalValue : 2 (10minutes * 2) = 20minutes interval....Value : 144(10m * 144) = 24 hours interval =>MAX( Default : 6 = One hour )
Size: 1 Byte, Default Value: 6

Setting Description
1 - 144 unit is per 10 minutes.you can change this value using configuration command class.

Technical Data

Hardware Platform ZM5101
Device Type On/Off Power Switch
Network Operation Always On Slave
Firmware Version HW: 17 FW: 41.208
Z-Wave Version 6.61.00
Certification ID ZC10-17075712
Z-Wave Product Id 0x018C.0x0042.0x0002
Supported Meter Type Electric Energy
Firmware Updatable Updatable by Manufacturer Representative
Color White
Supported Notification Types Power Management
Frequency XXfrequency
Maximum transmission power XXantenna
South KoreaOn/Off Power Switch