Popp

Mold detector

SKU: POPE700878

ZWave+ Security

Quickstart

This is a secure Routing Notification Sensor for XXXQFrequencyName. To run this device please insert fresh 1 * 1/2 AA batteries. To run this device please make sure the internal battery is fully charged. Tripple clicking the tamper button includes (adds) and excludes (removes) the device. A click on the tamper witch will wakeup the device. The device supports the Security S2 framework with unauthenticated network keys. Please follow the instructions on the central controller when including. The device also supports Smart Start. Please scan the QR code on the outlet cover of the device and your controller will add the the device automatically when powered up.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

This device measures the three air quality parameters temperature, humidity and dew point an reports them to a central controller. Beside this the device can directly control groups of other Z-Wave devices on over- and undershooting a set temperature and/or humidity parameter. This can be used to establish control loops for temperature and humidity. The device wakes up every 15 minutes to measure the values and it will send unsolicited reports when values change. Additionally the device will report all values on request.
The mold detector is actively monitoring the danger of mold in a room based on the temperature and humidity and will issue alarm warnings when criticical air conditions met. Wireless Alarm and  red and a green blinking LED will indicate a mold condition. This local LED warning function is also available when the device is not included in any Z-Wave network and works stand alone.

Installation

As first step you need to power the device by insertng the batteries. To access the battery compartment you need ot open the enclosure. this possible with any shap tool such as screwdriver using as leverage on one or more of the opening gaps (see image). It is also possible ot use a tool and open the device on the inlet coevrs (see image) but here you need to take care not to damage the device surface. The device can be placed on every flat surface or flat wall. Please note that air need to flow into the perforated part of the cover to reah the teperature and humidity sensor.

Product Usage

Once the device is powered up it will start monitoring the air parameters and warn of mold using the local red and green LED. All air parameters are measured every 15 minutes. Pushing the button will force an immediate measurement and the LEDs will indicate the danger of mold

  • green: no danger of mold in the room
  • red: danger of mold, oen the windows to lower the humidity
The device contains three sensors with the following accuracy measures:
  • Humidity: +/- 3 % on relative humidity, +/-1 % hysteresis
  • Temperature: 0 ... 65 grd C +/- 1 Kelvin
  • Dew Point: 0 ... 65 grd C +/- 1 Kelvin (calculated from other sensor values)

The device sends the following notifications to the central controller:
  • Moisture Alarm(0x10 - 0x02)
Reset to factory default Once Cover is removed and tamper switch is tripped, push the tamper for 5 seconds until red LED blinks. Then release tamper and push it again for 5 seconds until LED blinks.
Inclusion Tripple clicking the tamper button includes (adds) the device.
Exclusion Tripple clicking the tamper button excludes (removes) the device.
NIF Tripple Click the tamper button
Wakeup A single click on the tamper button will wakeup the device.
Protection XXXProtection
FirmwareUpdate No special action needed.
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 Lifeline
2 5 Temperature High Trigger
3 5 Temperature Low Trigger
4 5 Humidity High Trigger
5 5 Humidity Low Trigger

Configuration Parameters

Parameter 1: Minimum Temperature change to report

This value defines the minimum change of temperature to cause an unsolicited report of humidity to the central controller using Lifeline.
If the value is set to 0, there will be no reports sent to the controller, when the temperature changes. However, periodic reports, managed by configuration parameter 4, may still be active.
Size: 1 Byte, Default Value: 20

Setting Description
1 - 100 1/10 degree
0 disabled

Parameter 2: Minimum humidity change to report

This value defines the minimum change of humidity to cause an unsolicited report of humidity to the central controller using Lifeline.
If the value is set to 0, there will be no reports sent to the controller, when the humidity changes. However, periodic reports, managed by configuration parameter 4, may still be active.
Size: 1 Byte, Default Value: 7

Setting Description
1 - 20 %
0 disabled

Parameter 4: Periodic Reports

This parameter defines the time interval to send an unsolicited report.
If the value is set to 0, there will be no periodic reports sent to the controller. However, reports on temperature/humidity changes, managed by configuration parameters 1 and 2, may still be active.
Size: 2 Byte, Default Value: 43200

Setting Description
900 - 65535 Seconds
0 disabled

Parameter 5: Temperature Upper Watermark value

This parameter defines a temperature. If the measured temperature surpasses this watermark a BASIC command is sent into Association Group 2
Size: 2 Byte, Default Value: 0

Setting Description
1 - 1000 1/10 degree
0 disabled

Parameter 6: Temperature Lower Watermark value

This parameter defines a temperature. If the measured temperature dropps below this watermark a BASIC command is sent into Association Group 3
Size: 2 Byte, Default Value: 0

Setting Description
-200 - 1000 1/10 degree
0 disabled

Parameter 7: Humidity Upper Watermark value

This parameter defines a relative humidity. If the measured relative humidity surpasses this watermark a BASIC command is sent into Association Group 4
Size: 1 Byte, Default Value: 0

Setting Description
10 - 100 %
0 disabled

Parameter 8: Humidity Lower Watermark value

This parameter defines a relative humidity. If the measured temperature dropps below this relative humidity a BASIC command is sent into Association Group 5
Size: 1 Byte, Default Value: 0

Setting Description
1 - 90 %
0 disabled

Parameter 9: Low Temperature Trigger BASIC Set Command Value

This defines what BASIC command shall be sent out into association group 3
Size: 1 Byte, Default Value: 255

Setting Description
0 - 255 Value

Parameter 10: High Temperature Trigger BASIC Set Command Value

This defines what BASIC command shall be sent out into association group 2
Size: 1 Byte, Default Value: 0

Setting Description
0 - 255 Value

Parameter 11: Low Humidity Trigger BASIC Set Command Value

This defines what BASIC command shall be sent out into association group 5
Size: 1 Byte, Default Value: 255

Setting Description
0 - 255 Value

Parameter 12: High Humidity Trigger BASIC Set Command Value

This defines what BASIC command shall be sent out into association group 4
Size: 1 Byte, Default Value: 0

Setting Description
0 - 255 Value

Technical Data

Dimensions 25x25x10 mm
Hardware Platform ZM5101
EAN 4251295700878
IP Class IP 20
Battery Type 1 * 1/2 AA
Device Type Notification Sensor
Generic Device Class Notification Sensor
Specific Device Class Routing Notification Sensor
Firmware Version 1.0
Z-Wave Version 6.02
Z-Wave Product Id 0154.0014.0004
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeNotification Sensor