This is a
This solar powered outdoor siren can be used without any additional power supply or batteries. It can be installed on any place on the outside of the house and can be controlled using Z-Wave. The device will issue a very loud sound (105 dBm) and in parallel some stroboscope light as well. The siren is self-protecting. Removing the main device from the mounting unit immediately starts the siren and also reports the tamper attempt to the ZWave central controller. All communication between the Z-Wave controller and the siren is encrypted and secured to protect against manipulation. Thanks to the large solar panel, the siren can be mounted on nearly every place outside the house where it"s recommended to place it in indirect sun light to prevent strong heating-up the housing. The siren is maintenance-free and water-proofed (IP56). The average solar energy of one day keeps the device alive for up to 50 days (without using the siren).
The working range of the siren is: -10°C to +50°C
The siren can be placed on every location outside the home. Thanks to rating IP56 the location does not even need to be dry but please make sure it is placed high enough so that children do not accidently remove it. The device is self-protected against tamper and theft. In a first step the mounting plate (isee illustration above) is placed on the wall using the 4 screws provided. It is recommended to mount the complete device 5 mm from the wall for better sound.
The siren can be turned on and off using wireless commands. To protect this communication from misuse is strongly recommended to operate the siren in secure communication mode. The secure communication is activated on default during inclusion unless explicitly suppressed. When activated the siren will generate a 105 dB alarm sound and a flash light. This behavior can be configured as well using configuration parameter 5. Make sure to deactivate the tamper protection before removing an included siren from the mounting plate.
It is possible ot power the Siren from an external power supply. Please use any 12 V DC power with minimum of 1 W output. The terminals marked with E ( see ill1 for more details) allows to connect the power source to the device. its recommended ot detach the cables to the solar cell in this operating mode.
Reset to factory default | To reset the device keep the inclusion button pushed for 10 seconds. After 5 seconds the LED starts flashing and after another 5 seconds there is a short beep signaling the successful reset back to factory defaults. Use this procedure only when the network primary controller is missing or otherwise inoperable. |
Inclusion | 1. Remove the metal mounting plate from the device.
2. Open the case and turn on the power switch 3. Press the button once. |
Exclusion | 1. Deactivate the theft protection via parmeter 1.
2. Remove the siren from its mount.
3. Open the case.
4. Press the button once. |
NIF | Hit the Z-Wave Button |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | For a firmware update you need to open the siren?s housing first. Now, you can start the update process with your gateway. Please press the Z-Wave button twice fast, as soon as the single red LED (circuit board under the acrylic glass cover) blinks. The update will take around 10 minutes.After the update, the Siren will acticate on. Press the button to disable the siren. |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Z-Wave Plus Lifeline |
Sets the tamper triggering mode when removed from the holder Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Triggers automatically when it is removed from the holder. Must be turned off, using the button or from the controller |
1 | Triggers automatically when it is removed from the holder and turns off, when placed back on the holder |
2 | Does not trigger at all, when removed from the holder. Service Mode |
Determines how the Siren shall react on alarm Size: 1 Byte, Default Value: 2
Setting | Description |
---|---|
0 | Siren Only |
1 | Flash Only |
2 | Flash plus Siren |
If the value is set, the siren will be switched off automatically after a defined alarm time in Minutes. Size: 1 Byte, Default Value: 5
Setting | Description |
---|---|
0 | No Auto Off |
1 - 127 | after X Minutes |
Dimensions | 300x190x68 mm |
Weight | 893 gr |
Hardware Platform | ZM5202 |
EAN | 0019962700854 |
IP Class | IP 44 |
Voltage | 12 v |
Battery Type | 1 * Lithium 2400mAh |
Device Type | Siren |
Generic Device Class | Binary Switch |
Firmware Version | 02.06 |
Z-Wave Version | 06.02 |
Z-Wave Product Id | 0154.0004.0002 |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |