Quickstart

This is a Alarm Notification Sensor for XXXQFrequencyName. To run this device please insert fresh 1 * CR123A batteries. To run this device please make sure the internal battery is fully charged. A single click on the Z-Wave button inside the device includes and excludes the device.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

The Flood Sensor is a universal Z-Wave compatible flood sensor indicating water leakage in Smart Homes. In case of a detected incident the device will send an alarm message to a central controller and can in parallel directly control a group of devices, e.g. to shut off water supply. On the device it self the water event will be indicated using a red LED and a buzzer. This behavior can be configured. The device can be mounted on a wall for easy maintenance and the water is detected using a cabled detector head. The cable is 90 cm long. The device can also be used without the mounting base and will then flow on the water surface.

Installation


The device can be placed on any flat surface in front or below home appliances such as dishwashers or washing machines as long as the opening gap is higher than 25 mm.  The recommended way to install the device is to mount the mounting base on the lower part of the wall closed to the point of water leakage control. When mounted on a wall the device can be attached using the double sides tape on the backside of the device. However it is recommended to screw the device holder to the wall as seen above.

The detecting head is then connected to the base using a 90 cm long cable and can be placed even on placed with very limited room. To open the device turn the two parts of the enclosure against each other. The Z-Wave button is inside the enclosure.

Product Usage

Once placed on the desired location the device will alarm wirelessly and locally in case of a detected water leakage. The LED starts blinking and - if configured this way - the buzzer will sound. The sound will stop after 3 minutes even if the reason for the alarm was not removed. The LED will however continue to blink.

Reset to factory default Reset to Default: 10s HOLD Device Reset (5seconds LED start blinking, success -> short beep)
Inclusion Single click the internal Button. The red LED will light up to confirm the action.
Exclusion Single click the internal Button. The red LED will light up to confirm the action.
NIF Single click the internal Button. The red LED will light up to confirm the action.
Wakeup Double click the internal Button. The red LED will light up to confirm the action.
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 Lifeline
2 5 Water is detected

Configuration Parameters

Parameter 1: Flood Alarm Basic On Value

This BASIC Command Value is sent on flood alarm to all devices in Association Group 2
Size: 1 Byte, Default Value: 255

Setting Description
0 - 255 BASIC Command Value

Parameter 2: Flood Alarm Basic Off Value

This BASIC Command Value is sent on flood alarm clearance to all devices in Association Group 2
Size: 1 Byte, Default Value: 0

Setting Description
0 - 255 Basic Command Value

Parameter 3: Enable Buzzer Sound on Alarm

Enable/Disable the Buzzer sound on active alarms. The LED will remain blinking even when the buzzer is deactivated.
Size: 1 Byte, Default Value: 1

Setting Description
0 Disabled
1 Enabled

Technical Data

Dimensions 68 x 68 x 34 mm
Weight 48.54 gr
Hardware Platform ZM5202
EAN 4251295700052
IP Class IP 44
Load 1.3 yA
Battery Type 1 * CR123A
Device Type Notification Sensor
Generic Device Class Binary Sensor
Specific Device Class Alarm Notification Sensor
Network Operation Reporting Sleeping Slave
Firmware Version 00.03
Z-Wave Version 04.05
Z-Wave Product Id 0154.0004.0008
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeNotification Sensor