Netplus
Netplus Smart Dimmer Module 2-channel Zigbee
SKU: NPLZDIM02
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
Netplus Smart Dimmer Module 2-channel Zigbee is a compound smart dimmer switch, and it can be installed behind exising 2-way impulse or push button switches, in a distribution box or in a ceiling fitting. Then you will enable to turn on/off the lights, or adjust luminous intensity to your mood by using your cellphone from anywhere.
Flexible Installation.
Netplus smart LED dimmer 220V is originally designed to be compatible with existing impulse or push-button dimmer switch, keeping its mechnical function and at the minimum change of your current electrical system or lights. Thanks to its miniature size, this Tuya dimmer module fits most of the flush mounted junction boxes and light switch sockets, with no need of recontruction or rewiring. What’s more, one mounting clip is available with the Tuya smart light dimmer, which enable it installed on the DIN rail of a distribution box.
Zigbee Connected.
Connect this smart curtain module to one Zigbee 3.0 HUB or gateway, which is purchased individually.
Highly Compatibility.
This smart curtain module is compatible with existing curtain switches.
Time Schedule.
Create custom schedules based on your agenda or follow the sunrise or sunset.
Mobile App Remote Control.
Forgot to turn off your home lights because you were in a hurry? Now you can do it on your way to the office or the airport. Just take out your phone and slightly tap on the screen.
Perfect Illumination.
Every space in your house has its function which may vary for every family member. Netplus smart home dimmer will help you set the luminous intensity to create unique atmosphere for reading, relax or sleep.
Hand-free Voice Control.
Netplus smart devices work with amazon Alexa/Echo/Dot, Google Home, Yandex, etc. After pairing with them, you can control your home appliances with simple voice commands, no need to touch a switch or open the app, just ask Alexa to proceed commands.
Device Sharing.
Add your family members in the sharing list, then they are capable of controlling the same devices.
2-way Control for Stairs Lights.
Netplus smart relay or dimmer modules have more potential functions to surprise you. Connect it with a pair of 2-way switches to turn on/off the staircase lights.
Smart Scenarios.
Set the smart module to activate custom scenes based on temperature, humidity, light, or various occurrences. Use Netplus gate smart module to open your swing gate when you drive home, then smart switch turn on lights, air conditioning during the period of parking car.
Features:
- Input: AC100-240V 50/60Hz
- Output: AC100-240V 50/60Hz
- Load: max. 100W/channel x 2 channels
- Dimming Type: Triac dimmable (Trailing edge dimming)
- Power Measurement: No
- Operation Range: < 200 meters
- Standby Power: < 0.5W
- Overload Protection: Yes
- Neutral Wire Required: Yes
- Connectivity Protocol: Zigbee 3.0 mesh
- Operation Temperature: -10ºC – +40ºC
- Case Temperature: Tc: +80ºC (Max.)
- Working Humidity: 5% – 95% RH, non-condensing
- IP Rating: IP20 for indoor use
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| Dimensions | 0.0430000x0.0630000x0.0230000 mm |
| Weight | 34 gr |
| EAN | 4251295701967 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.