myStrom

myStrom WiFi LED Strip Controller

SKU: MYSLWRS1


Quickstart

This is a Z-Wave Device for . To run this device please connect it to your mains power supply.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

myStrom WiFi LED Strip Controller - The best Controller for your home. It brings each LED Strip to the next level and makes it Smart Home compatible. The Controller as a standalone device – without Strip nor Power Adapter. Suitable for RGBW Strips. 24 VDC Voltage. Designed in Switzerland.

The Best thing that could happen to your Strips.
The myStrom WiFi LED Strip Controller is the best controller you can buy for your home. It supports RGBW, monochrome and warm/cool tone LED Strips and makes them Smart Home compatible.

The myStrom Advantage.
The myStrom App enriches your LED Strips with many useful features e.g. Timer, Actions, Scenes or Holiday Mode. If you add a myStrom WiFi Button, you can also control your lights from the comfort of your couch. And thanks to the myStrom Skills, your LED Lights obey to the voice controls of Alexa and Assistant.

Perfect for Own Brand Smart Homes.
myStrom WiFi LED Strip Controllers can be integrated to many proprietary systems, e.g. Conrad Connect, FTTT, Control4 and Node-RED, also via REST API.

Installation, please note:
Scope of delivery:
The myStrom WiFi LED Strip Controller is delivered with attached connection cables for a transformer (round plug) and e.g. for an RGBW Strip (5 pin, incl. terminal). You can get the transformer from a specialised online shop. If you require a 12V Strip transformer, you need to purchase one separately.

LED Strip:
The LED Strip has a connection cable with adapted terminal: [1] Plug in together.
The LED Strip has a connection cable: [2] Screw it onto the terminal – remove the cover and replace the cable.
The LED Strip has no connection cable: [3] Solder it.
We recommend installation by a specialist in all cases.

Features:

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

  1. Make sure a device is in factory reset state before including. In doubt exclude before include.
  2. If inclusion still fails, check if both devices use the same frequency.
  3. Remove all dead devices from associations. Otherwise you will see severe delays.
  4. Never use sleeping battery devices without a central controller.
  5. Dont poll FLIRS devices.
  6. Make sure to have enough mains powered device to benefit from the meshing

Technical Data

Dimensions 0.0350000x0.3600000x0.0250000 mm
Weight 85 gr
EAN 7629999268340
Frequency XXfrequency
Maximum transmission power XXantenna

Explanation of Z-Wave specific terms