HomeSeer

Z-Wave RGB Fan Controller

SKU: HS-FC200+

ZWave+ Security V2

Quickstart

This is a secure Fan Switch for XXXQFrequencyName. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:
Inclusion: Add the device into your network by a Z-Wave certified controller. HS-FC200+ supports the latest S2 security offered by Z-Wave certified controllers. If your controller supports S2, please refer to the user guide of the controller for detailed instructions on adding devices to the network. You should be able to add HS-FC200+ into your network using the unique QR code or the DSK 5 digit pin located on the product or packaging. In addition, the device can be added or removed using the following 2-step procedure:1. Put your Z-Wave controller into Inclusion mode. Consult your controller manual if you're unsure how to do this.2. Tap the paddle of your new HomeSeer switch to begin the inclusion process. This will take a few moments to complete.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.
Attention: This manual is automatically generated from Z-Wave Alliance Product data and may be incomplete. Please refer to the Manufacturers Manual for more information.

Product Description

HS-FC200+ is a Z-Wave controllable wired fan controller for use with 3-speed or 4-speed ceiling fans. It has a vertical row of LEDs that indicate the fan speed level. Works with 3-speed or 4-speed fans only 4 segment LED dim level indicator Remotely or manually turns ON or OFF, or fan speed level Fits standard wall plates (wall plate not included) Works with any certified gateway supporting Z-Wave
Reset to factory default To be used only in the event that the network primary controller is lost or otherwise inoperable. (1) Turn switch on by tapping the top of the paddle once. (2) Quickly ap top of the paddle 3 times. (3) Quickly tap bottom of paddle 3 times. (4) If the LED turns off then on again, switch is reset. If not, repeat manual rest.
Inclusion Inclusion: Add the device into your network by a Z-Wave certified controller. HS-FC200+ supports the latest S2 security offered by Z-Wave certified controllers. If your controller supports S2, please refer to the user guide of the controller for detailed instructions on adding devices to the network. You should be able to add HS-FC200+ into your network using the unique QR code or the DSK 5 digit pin located on the product or packaging. In addition, the device can be added or removed using the following 2-step procedure:1. Put your Z-Wave controller into Inclusion mode. Consult your controller manual if you're unsure how to do this.2. Tap the paddle of your new HomeSeer switch to begin the inclusion process. This will take a few moments to complete.
Exclusion Exclusion: Remove the device from your network by a Z-Wave certified controller. HS-FC200+ supports the latest S2 security offered by Z-Wave certified controllers. If your controller supports S2, please refer to the user guide of the controller for detailed instructions on removing devices from the network. You should be able to remove HS-FC200+ into your network using the unique QR code or the DSK 5 digit pin located on the product or packaging. In addition, the device can be added or removed using the following 2-step procedure:1. Put your Z-Wave controller into Exclusion mode. Consult your controller manual if you're unsure how to do this.2. Tap the paddle of your new HomeSeer switch to begin the Exclusion process. This will take a few moments to complete.
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 Z-Wave Plus Lifeline

Configuration Parameters

Parameter 13: Sets LED indicator mode of operation

0=Fan Controller LED acts like a Fan Controller1=Fan Controller LED acts like a status indicator (LEDs should display the current fan speed level when you tap the paddle)
Size: 1 Byte, Default Value: 0

Setting Description
0 - 1 0=Fan Controller LED acts like a Fan Controller 1=Fan Controller LED acts like a status indicator (LEDs should display the current fan speed level when you tap the paddle)

Parameter 14: Sets the Normal mode LED color

Sets the default LED color when the Fan Controller is NOT in status mode. All LEDS will use this color in this mode. The color values are:0=White1=Red2=Green3=Blue4=Magenta5=Yellow6=Cyan
Size: 1 Byte, Default Value: 0

Setting Description
0 - 6 Sets the default LED color when the Fan Controller is NOT in status mode. All LEDS will use this color in this mode. The color values are:0=White 1=Red 2=Green 3=Blue 4=Magenta 5=Yellow 6=Cyan

Parameter 21: Sets status mode LED 1 bottom color

Sets status mode LED 1 bottom color0=Off1=Red2=Green3=Blue4=Magenta5=Yellow6=Cyan7=White
Size: 1 Byte, Default Value: 0

Setting Description
0 - 7 Sets status mode LED 1 bottom color0=Off 1=Red 2=Green 3=Blue 4=Magenta 5=Yellow 6=Cyan 7=White

Parameter 22: Sets status mode LED 2 color

Sets status mode LED 2 color0=Off1=Red2=Green3=Blue4=Magenta5=Yellow6=Cyan7=White
Size: 1 Byte, Default Value: 0

Setting Description
0 - 7 Sets status mode LED 2 color0=Off 1=Red 2=Green 3=Blue 4=Magenta 5=Yellow 6=Cyan 7=White

Parameter 23: Sets status mode LED 3 color

Sets status mode LED 3 color0=Off1=Red2=Green3=Blue4=Magenta5=Yellow6=Cyan7=White
Size: 1 Byte, Default Value: 0

Setting Description
0 - 7 Sets status mode LED 3 color0=Off 1=Red 2=Green 3=Blue 4=Magenta 5=Yellow 6=Cyan 7=White

Parameter 24: Sets status mode LED 4 color

Sets status mode LED 4 color0=Off1=Red2=Green3=Blue4=Magenta5=Yellow6=Cyan7=White
Size: 1 Byte, Default Value: 0

Setting Description
0 - 7 Sets status mode LED 4 color0=Off 1=Red 2=Green 3=Blue 4=Magenta 5=Yellow 6=Cyan 7=White

Parameter 3: Nightlight Mode

Nightlight Mode, sets bottom LED operation (in normal mode).0= bottom LED on if load is off.1= off if load is off
Size: 1 Byte, Default Value: 1

Setting Description
0 - 1 0= bottom LED on if load is off. 1= off if load is off

Parameter 30: Sets the Blink frequency for All LEDs in Status mode

Sets the Blink frequency for All LEDs in Status modePossible values: 0-2550= No blink, 1=100ms (100 ms off then 100ms on)
Size: 1 Byte, Default Value: 0

Setting Description
0 - 255 0= No blink, 1=100ms (100 ms off then 100ms on)

Parameter 31: Sets LEDs 1-4 to Blink in Status mode

Bitmask defines specific LEDs to enable for blinking.Note: this decimal value is derived from a hex code calculation based on the following:0x01 = led 10x02 = led 20x04 = led 30x08 = led 40 = All LED's disabled1 = LED 12 = LED 23 = LED 1 and 24 = LED 35 = LED 3 and 16 = LED 3 and 27 = LED 3 and 2 and 18 = LED 49 = LED 4 and 110 = LED 4 and 211 = LED 4 and 2 and 112 = LED 4 and 313 = LED 4 and 3 and 114 = LED 4 and 3 and 215 = LED 4 and 3 and 2 and 1
Size: 1 Byte, Default Value: 0

Setting Description
0 - 15 0 = All LEDs disabled 1 = LED 1 2 = LED 2 3 = LED 1 and 2 4 = LED 3 5 = LED 3 and 1 6 = LED 3 and 2 7 = LED 3 and 2 and 1 8 = LED 4 9 = LED 4 and 1 10 = LED 4 and 2 11 = LED 4 and 2 and 1 12 = LED 4 and 3 13 = LED 4 and 3 and 1 14 = LED 4 and 3 and 2 15 = LED 4 and 3 and 2 and 1

Parameter 4: Sets paddles load orientation

Sets whether the top or the bottom paddle turns the load ON
Size: 1 Byte, Default Value: 0

Setting Description
0 - 1 0 = Top On 1 = Bottom On

Parameter 5: Sets fan type

Sets the supported fan type, 3 or 4 speed
Size: 1 Byte, Default Value: 0

Setting Description
0 - 1 0=3 speed fan 1=4 speed fan

Technical Data

Hardware Platform ZM5101
Device Type Fan Switch
Network Operation Always On Slave
Firmware Version HW: 255 FW: 50.01
Z-Wave Version 6.81.00
Certification ID ZC10-18066137
Z-Wave Product Id 0x000C.0x0203.0x0001
Outdoor Use ok
Electric Load Type Inductive (e.g. Motor)
Z-Wave Scene Type Scene & Central Scene
Switch Type Decorator Paddle Rocker
Neutral Wire Required ok
Firmware Updatable Updatable by Consumer by RF
Color White
Frequency XXfrequency
Maximum transmission power XXantenna
U.S. / Canada / MexicoFan Switch