This is a
(1) Make sure the power supply is disconnected and the RGB BULB is located within a direct Z-Wave network"s main controller communication range.
(2) Set the Z-Wave network main controller into learning mode (see Z-Wave network controller operating manual).
(3) Insert the RGB BULB into a lamp-socket and then power on.
(4) Auto-inclusion will be activated. If the inclusion is successful, the RGB BULB will blink fast in blue for less than 5 seconds and then keep on for 3 seconds. RGB BULB will keep the same color as befor the inclusion.
To include RGB BULB into a Z-Wave network as a security device:
(1) Screw in the RGB BULB.
(2) Set the Z-Wave network main controller into learning mode (see Z-Wave network controller operating manual).
(3) Toggle the wall switch off and on 3 times quickly (within 3 seconds and the final ending position of the wall switch must be on).
(4) If the inclusion is successful, the RGB BULB will blink fast in green for less than 5 seconds and then keep on 3 seconds. RGB BULB will keep on the same color before it is included into the Z-Wave network.
RGB Bulb is a smart bulb enables Z-Wave remote command and control (on/off/dim). It has over 16,000,000 colors, you can choose its color according to your favour.
RGB BULB is simple to install and use.
(1) Before installation make sure the power supply is disconnected.
(2) Screw in the RGB BULB
(3) Power it on.
(4) Include the RGB BULB into your Z-Wace netzwork
(5) Select a color if necessary
SELECT A LIGHT COLOR
Screw in the RGB BULB.
Toggle the wall switch off and on 2 times quickly(within 2 seconds and the final ending position of the wall switch must be on), the RGB BULB will blink fast in purple for 1 second, which indicate the RGB BULB is successfully set into color switch mode. Light color will cyclic change in order of: warm white, cool white, red, green, blue, warm white.
TIP: You can repeat step 2 to select another color.
Reset to factory default | There are two ways to reset the RGB BULB. One way is to remove RGB BULB from the Z-Wave network, the other way is to use the configuration command class. |
Inclusion | To include RGB BULB into a Z-Wave network as a non-security device: (1) Make sure the power supply is disconnected and the RGB BULB is located within a direct Z-Wave network"s main controller communication range. (2) Set the Z-Wave network main controller into learning mode (see Z-Wave network controller operating manual). (3) Insert the RGB BULB into a lamp-socket and then power on. (4) Auto-inclusion will be activated. If the inclusion is successful, the RGB BULB will blink fast in blue for less than 5 seconds and then keep on for 3 seconds. RGB BULB will keep the same color as befor the inclusion. To include RGB BULB into a Z-Wave network as a security device: (1) Screw in the RGB BULB. (2) Set the Z-Wave network main controller into learning mode (see Z-Wave network controller operating manual). (3) Toggle the wall switch off and on 3 times quickly (within 3 seconds and the final ending position of the wall switch must be on). (4) If the inclusion is successful, the RGB BULB will blink fast in green for less than 5 seconds and then keep on 3 seconds. RGB BULB will keep on the same color before it is included into the Z-Wave network. |
Exclusion | (1) Screw in the RGB BULB. (2) Set the Z-Wave network main controller into excluding mode (see Z-Wave controller operating manual). (3) Toggle the wall switch off and on 3 times quickly(within 3 and the final ending position of the wall switch must be on), if the exclusion is successful, the RGB BULB will blink fast in orange for less than 5 seconds and then keep on for 3 seconds. RGB BULB will keep on warm white after the exclusion procedure is finished. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Z-Wave Plus Lifeline: RGB BULB will send the follow notification to the associated nodes whenthe status of the RGB BULB is changed.1. Set Configuration parameter 24 to 0: Reserved2. Set Configuration parameter 24 to 1: Send Basic Report3. Set Configuration parameter 24 to 2: Send Basic Report only when thestatus of the RGB BULB is not changed by Z-WAVE Command. |
Define how the RGB BULB will react after the power supply is back on. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | RGB BULB memorizes its state after a power failure. |
1 | RGB BULB does not memorize its state after a power failure. Connected device will be on after the power supply is reconnected |
2 | RGB BULB does not memorize its state after a power failure. Connected device will be off after the power supply is reconnected |
RGB BULB can send notifications to associated device (Group Lifeline)when the status of the RGB BULB is changed. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | The function is disabled |
1 | Send Basic report |
2 | Send BASIC REPORT only when the status of the RGB BULB is not changed by Z-WAVE command. |
This Parameter enable or disable the function of using wall switch to turn on or off RGB Bulb Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable |
1 | Enable |
RGB Bulb can blink or cyclic/random change color automatically at set intervals. It will stop blink or change color when reciving any control command like Basic Set. Size: 4 Byte, Default Value: 3072
Setting | Description |
---|---|
3072 | Stop changing |
16826368 | Color gradual change randomly |
33603584 | Color change randomly with a breathing blink |
50380800 | Blink with random color |
67158016 | Color change randomly |
285261824 | Color gradual change |
302039040 | Breathing blink with a specific color |
318816256 | Blink with a specific color |
RGB BULB will exclude from the Z-Wave network with thisparticular command. Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
1431655765 | Resetting to the factory default. |
Dimensions | 115x65 mm |
Weight | 123 gr |
Hardware Platform | ZM5101 |
EAN | 4251295700250 |
Voltage | 230V |
Load | 7,5W |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Z-Wave Version | 6.51.08 |
Certification ID | ZC10-16095230 |
Z-Wave Product Id | 0x0208.0x0101.0x0004 |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |