This is a
(1) Make sure the power supply is disconnected and the RGB BULB is located within a direct Z-Wave network"s main controller communication range.
(2) Set the Z-Wave network main controller into learning mode (see Z-Wave network controller operating manual).
(3) Insert the RGB BULB into a lamp-socket and then power on.
(4) Auto-inclusion will be activated. If the inclusion is successful, the RGB BULB will blink fast in blue for less than 5 seconds and then keep on for 3 seconds. RGB BULB will keep the same color as befor the inclusion.
To include RGB BULB into a Z-Wave network as a security device:
(1) Screw in the RGB BULB.
(2) Set the Z-Wave network main controller into learning mode (see Z-Wave network controller operating manual).
(3) Toggle the wall switch off and on 3 times quickly (within 3 seconds and the final ending position of the wall switch must be on).
(4) If the inclusion is successful, the RGB BULB will blink fast in green for less than 5 seconds and then keep on 3 seconds. RGB BULB will keep on the same color before it is included into the Z-Wave network.
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
RGB Bulb is a smart bulb enables Z-Wave remote command and control (on/off/dim). It has over 16,000,000 colors, you can choose its color according to your favour.
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.
There are two ways to reset the RGB BULB. One way is to remove RGB BULB from the Z-Wave network, the other way is to use the configuration command class.
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
RGB BULB is simple to install and use.
(1) Before installation make sure the power supply is disconnected.
(2) Screw in the RGB BULB
(3) Power it on.
(4) Include the RGB BULB into your Z-Wace netzwork
(5) Select a color if necessary
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
SELECT A LIGHT COLOR
Screw in the RGB BULB.
Toggle the wall switch off and on 2 times quickly(within 2 seconds and the final ending position of the wall switch must be on), the RGB BULB will blink fast in purple for 1 second, which indicate the RGB BULB is successfully set into color switch mode. Light color will cyclic change in order of: warm white, cool white, red, green, blue, warm white.
TIP: You can repeat step 2 to select another color.
Here are a few hints for network installation if things dont work as expected.
Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Z-Wave Plus Lifeline: RGB BULB will send the follow notification to the associated nodes whenthe status of the RGB BULB is changed.1. Set Configuration parameter 24 to 0: Reserved2. Set Configuration parameter 24 to 1: Send Basic Report3. Set Configuration parameter 24 to 2: Send Basic Report only when thestatus of the RGB BULB is not changed by Z-WAVE Command. |
Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.
IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.
Define how the RGB BULB will react after the power supply is back on. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | RGB BULB memorizes its state after a power failure. |
1 | RGB BULB does not memorize its state after a power failure. Connected device will be on after the power supply is reconnected |
2 | RGB BULB does not memorize its state after a power failure. Connected device will be off after the power supply is reconnected |
RGB BULB can send notifications to associated device (Group Lifeline)when the status of the RGB BULB is changed. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | The function is disabled |
1 | Send Basic report |
2 | Send BASIC REPORT only when the status of the RGB BULB is not changed by Z-WAVE command. |
This Parameter enable or disable the function of using wall switch to turn on or off RGB Bulb Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable |
1 | Enable |
RGB Bulb can blink or cyclic/random change color automatically at set intervals. It will stop blink or change color when reciving any control command like Basic Set. Size: 4 Byte, Default Value: 3072
Setting | Description |
---|---|
3072 | Stop changing |
16826368 | Color gradual change randomly |
33603584 | Color change randomly with a breathing blink |
50380800 | Blink with random color |
67158016 | Color change randomly |
285261824 | Color gradual change |
302039040 | Breathing blink with a specific color |
318816256 | Blink with a specific color |
RGB BULB will exclude from the Z-Wave network with thisparticular command. Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
1431655765 | Resetting to the factory default. |
Dimensions | 115x65 mm |
Weight | 123 gr |
Hardware Platform | ZM5101 |
EAN | 4251295700250 |
Voltage | 230V |
Load | 7,5W |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Z-Wave Version | 6.51.08 |
Certification ID | ZC10-16095230 |
Z-Wave Product Id | 0x0208.0x0101.0x0004 |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |