Qubino

Flush Dimmer 0-10V

SKU: GOAEZMNHVD1

ZWave+ Security

Quickstart

This is a secure 10V Dimmer for XXXQFrequencyName. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

Universal dimmer module with a standard 0-10V output and a multi-function input, which may be a push button / switch, a potentiometer or 0-10V signal.

  • Push button (mono stable switch)
  • Bi stable switch 
  • Potentiometer
  • 0-10V input (requires external source) 

Installation

 

  • Before the installation disconnect power supply (1224VDC)
  • Connect the module according to electrical diagram. 
  • Locate the antenna far from metal elements (as far as possible). 
  • Do not shorten the antenna.

Note! Do not connect the module to loads exceeding recommended values. Connect the module only in accordance to the below diagrams. Improper connections may be dangerous.



NOTE: When connecting temperature sensor to module that has already been included, you have to exclude module first. Switch off power supply, connect the sensor and re-include the module. 
Reset to factory default
  • press service button S for more than 6 second or 
  • press push button I1 five  times within 3s ( 5 times change switch state within 3 seconds) in the first 60 seconds after the module is connected to the power supply.
Inclusion
  • press service button S for more than 2 second or
  • press push button I1 three times within 3s (3 times change switch state within 3 seconds).
Exclusion
  • press service button S for more than 6 second or 
  • press push button I1 five  times within 3s ( 5 times change switch state within 3 seconds) in the first 60 seconds after the module is connected to the power supply.
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 1 Lifeline
2 16 basic on/off
3 16 start level change/stop level change
4 16 multilevel set 
5 16 multilevel sensor report (triggered at change of analogue sensor)
6 16 multilevel sensor report (triggered at change of temperature sensor) 

Configuration Parameters

Parameter 1: Input switch type


Size: 1 Byte, Default Value: 0

Setting Description
0 mono-stable switch type (push button)
1 bi-stable switch type

Parameter 5: Working mode

With this parameter is possible to change the module presentation on the user interface.

NOTE: After parameter change, first exclude module (without setting parameters to default value) then wait at least 30s and then re include the module!
Size: 1 Byte, Default Value: 0

Setting Description
0 Dimmer mode
1 Switch mode

Parameter 10: Activate / deactivate functions ALL ON / ALL OFF


Size: 2 Byte, Default Value: 255

Setting Description
255 ALL ON active, ALL OFF active.
0 ALL ON is not active, ALL OFF is not active
1 ALL ON is not active, ALL OFF active
2 ALL ON active, ALL OFF is not active DIN Dimmer module responds to commands ALL ON / ALL OFF that may be sent by the main controller or by other controller belonging to the system.

Parameter 11: Automatic turning off output after set time


Size: 2 Byte, Default Value: 0

Setting Description
0 Auto OFF disabled
1 - 32536 1 second - 32536 seconds Auto OFF enabled with define time, step is 1 second.

Parameter 12: Automatic turning on output after set time


Size: 2 Byte, Default Value: 0

Setting Description
0 Auto ON disabled
1 - 32535 1 second - 32535 seconds Auto ON enabled with define time, step is 1 second

Parameter 21: Enable/Disable Double click function

If Double click function is enabled, a fast double click on the push button will set dimming power at maximum dimming value.
Size: 1 Byte, Default Value: 0

Setting Description
0 double click disabled
1 double click enabled

Parameter 30: Saving the state of the device after a power failure


Size: 1 Byte, Default Value: 0

Setting Description
0 DIN Dimmer module saves its state before power failure (it returns to the last position saved before a power failure).
1 DIN Dimmer module does not save the state after a power failure, it returns to off position.

Parameter 40: Power reporting in Watts on power change

Set value means percentage, set value from 0 - 100=0% - 100%.

NOTE: if power changed is less than 1W, the report is not send (pushed), independent of percentage set.
Size: 1 Byte, Default Value: 5

Setting Description
0 reporting disabled
1 - 100 1% - 100% Reporting enabled. Power report is send (push) only when actual power in Watts in real time changes for more than set percentage comparing to previous actual power in Watts, step is 1%.

Parameter 42: Power reporting in Watts by time interval

Set value means time interval (0 – 32767) in seconds, when power report is send.
Size: 2 Byte, Default Value: 0

Setting Description
0 reporting disabled
1 - 32767 1 second - 32767 seconds. Reporting enabled. Power report is send with time interval set by entered value. Please note, that too fast reporting can cause too much Z-Wave traffic resulting in Z-Wave poor response

Parameter 60: Minimum dimming value

NOTE: The minimum level may not be higher than the maximum level! 1% min. dimming value is defined by Z-Wave multilevel device class
Size: 1 Byte, Default Value: 1

Setting Description
1 - 98 1% - 98%, step is 1%. Minimum dimming values is set by entered value.

Parameter 61: Maximum dimming value

NOTE: The maximum level may not be lower than the minimum level! 99% max. dimming value is defined by Z-Wave multilevel device class.
Size: 1 Byte, Default Value: 99

Setting Description
2 - 99 2% - 99%, step is 1%. Maximum dimming values is set by entered value.

Parameter 65: Dimming time (soft on/off)

Set value means time of moving the DIN Dimmer between min. and max. dimming values by short press of push button I or controlled through UI (BasicSet).
Size: 2 Byte, Default Value: 100

Setting Description
50 - 255 500 mseconds - 2550 mseconds (2,55s), step is 10 mseconds

Parameter 66: Dimming time when key pressed

Time of moving the DIN Dimmer between min. and max dimming values by continues hold of push button I or associated device.
Size: 2 Byte, Default Value: 3

Setting Description
1 - 255 1 second - 255 seconds

Parameter 67: Ignore start level

This parameter is used with association group 3. A receiving device SHOULD respect the start level if the Ignore Start Level bit is 0. A receiving device MUST ignore the start level if the Ignore Start Level bit is 1.


Size: 1 Byte, Default Value: 0

Setting Description
0 respect start level
1 ignore start level

Parameter 68: Dimming duration

This parameter is used with association group 3. The Duration field MUST specify the time that the transition should take from the current value to the new target value. A supporting device SHOULD respect the specified Duration value. 


Size: 1 Byte, Default Value: 0

Setting Description
0 dimming duration according to parameter 66
1 - 127 from 1 to 127 seconds

Parameter 110: Temperature sensor offset settings

Set value is added or subtracted to actual measured value by sensor.
Size: 2 Byte, Default Value: 32536

Setting Description
1 - 100 value from 0.1 °C to 10.0 °C is added to actual measured temperature.
1001 - 1100 value from -0.1 °C to -10.0 °C is subtracted to actual measured temperature.

Parameter 120: Digital temperature sensor reporting

If digital temperature sensor is connected, module reports measured temperature on temperature change defined by this parameter. 
Size: 1 Byte, Default Value: 5

Setting Description
0 reporting disabled
1 - 127 0,1°C - 12,7°C, step is 0,1°C

Parameter 250: Unsecure/Secure Inclusion (Version 2.04 or higher)


Size: 1 Byte, Default Value: 0

Setting Description
0 Unsecure
1 Secure

Technical Data

Dimensions 41,8x36,8x15,4 mm
Weight 28 gr
Hardware Platform ZM5202
EAN 3830062070553
IP Class IP IP20
Voltage 12-24V DC
Device Type 10V Dimmer
Generic Device Class Multilevel Switch
Firmware Version 02.04
Z-Wave Version 04.22
Certification ID ZC10-17025424
Z-Wave Product Id 0x0159.0x0001.0x0053
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
Europe10V Dimmer