Quickstart

This is a Z-Wave Device for XXXQFrequencyName. To run this device please connect it to your mains power supply. To add this device to your network execute the following action:



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

This Z-Wave module is used to regulate temperature. Regulation is done using full wave on/off technology. The module can be controlled either through Z-Wave network or through the wall switch. The module is designed to be mounted inside a “flush mounting box” and is hidden behind a traditional wall switch. Module measures power consumption of connected device. It is designed to act as repeater in order to improve range and stability of Z-Wave network.

Installation

- To prevent electrical shock and/or equipment damage, disconnect electrical power at the main fuse or circuit breaker before installation or any servicing.
- Make sure, that no voltage is present in the installation.
- Prevent the disconnecting device from being switched on accidentally.
- Connect the module according to electrical diagram.
- Locate the antenna far from metal elements (as far as possible).
- Do not shorten the antenna.



Functionality
To turn the module on or off the user can simply press once switch connected to I1 or by pressing on the button Auto in the GUI. When the module is turned on it automatically regulated the temperate based on Hysteresis on and Hysteresis off parameters settings. When the temperature is decreasing and reaches point 1 (defined by parameter 43), heating device is turned on and remains active until the temperature in the room is not increased to reach point 2 (defined by parameter 44). In this moment heating device is turned off. When heating device is turned off, then it is working in antifreeze regime. The antifreeze regime turns on heating device when the temperature is lower of equal to the temperature set by parameter 45.

Reset to factory default
  • press service button S for more than 6 second or 
  • press push button I1 five  times within 3s ( 5 times change switch state within 3 seconds) in the first 60 seconds after the module is connected to the power supply.
Inclusion
  • press service button S for more than 2 second or
  • press push button I1 three times within 3s (3 times change switch state within 3 seconds).
Exclusion
  • press service button S for more than 6 second or 
  • press push button I1 five  times within 3s ( 5 times change switch state within 3 seconds) in the first 60 seconds after the module is connected to the power supply.
NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 1 Lifeline
2 16 Basic on/off  (triggered at change of the output Q state and reflecting its state)
3 16 SENSOR_MULTILEVEL_GET (triggered once per minute if Parameter 121 is not 0)
4 16 Basic on/off (triggered by Too high temperature limit, it send FF)
5 16 THERMOSTAT_SETPOINT_GET (triggered once per minute if Parameter 121 is not 0)
6 16 Basic on/off (trigged by change of I1 if window sensor functionality is selected by parameter no. 11)
7 16 Basic on/off (trigged by change of I2 if condense sensor functionality is selected by parameter no. 12)
8 16 Basic on/off (trigged by change of I3 if flood sensor functionality is selected by parameter no. 13)
9 16 Sensor multilevel report (trigged by change of temperature)

Configuration Parameters

Parameter 1: Input I1 switch type


Size: 1 Byte, Default Value: 1

Setting Description
0 mono-stable switch type (push button)
1 bi-stable switch type

Parameter 2: Input I2 switch type


Size: 1 Byte, Default Value: 1

Setting Description
0 mono-stable switch type (push button)
1 bi-stable switch type

Parameter 3: Input I3 switch type


Size: 1 Byte, Default Value: 1

Setting Description
0 mono-stable switch type (push button)
1 bi-stable switch type

Parameter 4: Input 1 contact type

NOTE: This parameter has influence only when parameter no. 11 is set to the value “2”. After setting this parameter, switch the window sensor once, so that the module could determine the input state
Size: 1 Byte, Default Value: 0

Setting Description
0 NO (normally open) input type
1 NC (normally close) input type

Parameter 5: Input 2 contact type

NOTE: This parameter has influence only when parameter no. 12 is set to the value “2000”. After setting this parameter, switch the condense sensor once, so that the module could determine the input state.
Size: 1 Byte, Default Value: 0

Setting Description
0 NO (normally open) input type
1 NC (normally close) input type

Parameter 6: Input 3 contact type

NOTE: This parameter has influence only when parameter no. 13 is set to the value “2”. After setting this parameter, switch the flood sensor once, so that the module could determine the input state.
Size: 1 Byte, Default Value: 0

Setting Description
0 NO (normally open) input type
1 NC (normally close) input type

Parameter 10: Activate / deactivate functions ALL ON / ALL OFF

Flush on/off thermostat module responds to commands ALL ON / ALL OFF that may be sent by the main controller or by other controller belonging to the system.
Size: 2 Byte, Default Value: 255

Setting Description
255 ALL ON active, ALL OFF active.
0 ALL ON is not active, ALL OFF is not active
1 ALL ON is not active, ALL OFF active
2 ALL ON active, ALL OFF is not active

Parameter 11: I1 Functionality selection


Size: 2 Byte, Default Value: 1

Setting Description
1 input I1 changes the mode of the thermostat between Off and Heat/Cool. In this case function on window sensor is disabled
2 input I1 influences on heating/cooling valves according to status of window sensor. In this case function of Off and Heat/Cool selection by I1 is disabled
32767 input I1 doesn’t influence on the Heat/Cool process

Parameter 12: I2 Functionality selection


Size: 2 Byte, Default Value: 32676

Setting Description
0 - 990 Temperature set point from 0.0 °C to 99.0 °C. When I2 is pressed, it automatically set temperature setpoint according to value defined here. In this case function of condense sensor is disabled
1001 - 1050 Temperature set point from -0.1 °C to -15.0 °C. When I2 is pressed, it automatically set temperature setpoint according to value defined here. In this case function of condense sensor is disabled
2000 Input I2 influences on the cooling valve according to status of condense sensor, In this case function of setpoint selection with I2 is disabled
32767 input I2 does not influence on the Heat/Cool process

Parameter 13: I3 Functionality selection

NOTE: If this parameter is changed, it is necessary to reinclude the module.
Size: 2 Byte, Default Value: 32767

Setting Description
1 input I3 changes the mode of the thermostat between Heat and Cool and override parameter 59. In this case function on flood sensor is disabled
2 input I3 influences on heating/cooling valves according to status of flood sensor. In this case function of Heat/Cool selection by I3 is disabled
32767 input I3 does not influence on the heat/cool process

Parameter 40: Power reporting in Watts on power change

Set value means percentage, set value from 0 - 100=0% - 100%.

NOTE: if power changed is less than 1W, the report is not send (pushed), independent of percentage set.

Size: 1 Byte, Default Value: 5

Setting Description
0 reporting disabled
1 - 100 1% - 100% Reporting enabled. Power report is send (push) only when actual power in Watts in real time changes for more than set percentage comparing to previous actual power in Watts, step is 1%.

Parameter 42: Power reporting in Watts by time interval

Set value means time interval (0 – 32767) in seconds, when power report is send.
Size: 2 Byte, Default Value: 0

Setting Description
0 reporting disabled
1 - 32767 1 second - 32767 seconds. Reporting enabled. Power report is send with time interval set by entered value. Please note, that too fast reporting can cause too much Z-Wave traffic resulting in Z-Wave poor response

Parameter 43: Hysteresis On

This parameter defines temperature min difference between real measured temperature and set-point temperature to turn device on
Size: 2 Byte, Default Value: 1005

Setting Description
0 - 127 0.0 °C … 12.7 °C
1001 - 1127 -0.1°C ~ -12.7 °C

Parameter 44: Hysteresis Off

This parameter defines temperature min difference between real measured temperature and set-point temperature to turn device off.
Size: 2 Byte, Default Value: 5

Setting Description
0 - 127 0.0 °C - 12.7 °C
1001 - 1127 -0.1 °C ~ -12.7 °C

Parameter 45: Antifreeze

Set value means at which temperature the device will be turned on even if the thermostat was manually set to off. 
NOTE: Antifreeze is activated only in heating mode and it uses hysteresis from Par.34 and Par.44

Size: 2 Byte, Default Value: 50

Setting Description
0 - 127 0.0 °C - 12.7 °C
1001 - 1127 -0.1°C ~ -12.6 °C
255 Antifreeze functionality disabled

Parameter 59: Thermostat mode

If parameter changed it is necessary to re-include module.
Size: 1 Byte, Default Value: 0

Setting Description
0 Heat mode
1 Cool mode

Parameter 60: Too low temperature limit

Too low temperature limit is set by entered value. In case is set value out of this range, module is changing set value automatically to default value
Size: 2 Byte, Default Value: 50

Setting Description
1 - 1000 0.1°C to 100.0°C, step is 0.1°C
1001 - 1150 -0.1°C to -15.0°C

Parameter 61: Too high temperature limit

Too high temperature limit is set by entered value. In case the set value is out of this range, module is changing automatically set value to default value. 
Size: 2 Byte, Default Value: 700

Setting Description
1 - 1000 0.1°C - 100.0°C, step is 0.1°C.

Parameter 63: Output Switch selection

Set value means the type of the device that is connected to the on/off output. The device type can be normally open (NO) or normally close (NC).
Size: 1 Byte, Default Value: 0

Setting Description
0 When system is turned off the output is 0 V
1 When system is turned off the output is 230 V

Parameter 70: Input 1 status on delay

If the value of parameter is different to 0, means that the Influence of this input to heating or cooling will react after inserted time. This parameter has influence only when the window sensor functionality is selected by the parameter no. 11. 
NOTE: Device status on UI change immediately

Size: 2 Byte, Default Value: 0

Setting Description
1 - 32000 seconds

Parameter 71: Input 1 status off delay

If the value of parameter is different to 0, means that the Influence of this input to heating or cooling will react after inserted time. This parameter has influence only when the window sensor functionality is selected by the parameter no. 11.
NOTE: Device status on UI change immediately

Size: 2 Byte, Default Value: 0

Setting Description
1 - 32000 seconds

Parameter 72: Input 2 status on delay

If the value of parameter is different to 0, means that the Influence of this input to heating or cooling will react after inserted time. This parameter has influence only when the window sensor functionality is selected by the parameter no. 12. 
NOTE: Device status on UI change immediately

Size: 2 Byte, Default Value: 0

Setting Description
1 - 32000 seconds

Parameter 73: Input 2 status off delay

If the value of parameter is different to 0, means that the Influence of this input to heating or cooling will react after inserted time. This parameter has influence only when the window sensor functionality is selected by the parameter no. 12.
NOTE: Device status on UI change immediately

Size: 2 Byte, Default Value: 0

Setting Description
1 - 32000 seconds

Parameter 74: Input 3 status on delay

If the value of parameter is different to 0, means that the Influence of this input to heating or cooling will react after inserted time. This parameter has influence only when the window sensor functionality is selected by the parameter no. 13. 
NOTE: Device status on UI change immediately

Size: 2 Byte, Default Value: 0

Setting Description
1 - 32000 seconds

Parameter 75: Input 3 status off delay

If the value of parameter is different to 0, means that the Influence of this input to heating or cooling will react after inserted time. This parameter has influence only when the window sensor functionality is selected by the parameter no. 13.
NOTE: Device status on UI change immediately

Size: 2 Byte, Default Value: 0

Setting Description
1 - 32000 seconds

Parameter 100: Enable / Disable Endpoint I1 or select Notification Type and Event

Enabling I1 means that Endpoint (I1) will be present on UI. Disabling it will result in hiding the endpoint according to the parameter set value. Additionally, a Notification Type and Event can be selected for the endpoint.
NOTE1: After parameter change, first exclude module (without setting parameters to default value) and then re include the module! 
NOTE2: When the parameter is set to value 9 the notifications are send for Home Security.

Size: 1 Byte, Default Value: 0

Setting Description
0 Endpoint, I1 disabled
1 Home Security; Motion Detection, unknown location.
2 CO; Carbon Monoxide detected, unknown location.
3 CO2; Carbon Dioxide detected, unknown location.
4 Water Alarm; Water Leak detected, unknown location.
5 Heat Alarm; Overheat detected, unknown location
6 Smoke Alarm; Smoke detected, unknown location.
9 Sensor binary

Parameter 101: Enable / Disable Endpoint I2 or select Notification Type and Event

Enabling I2 means that Endpoint (I2) will be present on UI. Disabling it will result in hiding the endpoint according to the parameter set value. Additionally, a Notification Type and Event can be selected for the endpoint. Available configuration parameters (data type is 1 Byte DEC): Endpoint device type selection: - notification sensor (1 - 6): 
NOTE1: After parameter change, first exclude module (without setting parameters to default value) and then re include the module! 
NOTE2: When the parameter is set to value 9 the notifications are send for Home Security.

Size: 1 Byte, Default Value: 0

Setting Description
0 Endpoint, I1 disabled
1 Home Security; Motion Detection, unknown location.
2 CO; Carbon Monoxide detected, unknown location.
3 CO2; Carbon Dioxide detected, unknown location.
4 Water Alarm; Water Leak detected, unknown location.
5 Heat Alarm; Overheat detected, unknown location
6 Smoke Alarm; Smoke detected, unknown location.
9 Sensor binary

Parameter 102: Enable / Disable Endpoint I3 or select Notification Type and Event

Enabling I3 means that Endpoint (I3) will be present on UI. Disabling it will result in hiding the endpoint according to the parameter set value. Additionally, a Notification Type and Event can be selected for the endpoint. Available configuration parameters (data type is 1 Byte DEC): Endpoint device type selection: - notification sensor (1 - 6): 
NOTE1: After parameter change, first exclude module (without setting parameters to default value) and then re include the module! 
NOTE2: When the parameter is set to value 9 the notifications are send for Home Security.

Size: 1 Byte, Default Value: 0

Setting Description
0 Endpoint, I1 disabled
1 Home Security; Motion Detection, unknown location.
2 CO; Carbon Monoxide detected, unknown location.
3 CO2; Carbon Dioxide detected, unknown location.
4 Water Alarm; Water Leak detected, unknown location.
5 Heat Alarm; Overheat detected, unknown location
6 Smoke Alarm; Smoke detected, unknown location.
9 Sensor binary

Parameter 110: Temperature sensor offset settings

Set value is added or subtracted to actual measured value by sensor.
Size: 2 Byte, Default Value: 32536

Setting Description
1 - 100 value from 0.1 °C to 10.0 °C is added to actual measured temperature.
1001 - 1100 value from -0.1 °C to -10.0 °C is subtracted to actual measured temperature.

Parameter 120: Digital temperature sensor reporting

If digital temperature sensor is connected, module reports measured temperature on temperature change defined by this parameter. 
Size: 1 Byte, Default Value: 5

Setting Description
0 reporting disabled
1 - 127 0,1°C - 12,7°C, step is 0,1°C

Parameter 121: Digital temperature sensor / setpoint selector

If digital temperature sensor is not connected, module can grab measured temperature from external secondary module.
Size: 1 Byte, Default Value: 0

Setting Description
0 internal digital temperature sensor is mounted, setpoint is set by controller
1 (bit 0) temperature is grabbed from external always on sensor with sensor_multilevel_get sent by association 3
2 (bit 1) temperature is grabbed from external battery powered room sensor declared in parameter 122
3 (bit 2) setpoint is grabbed from external always on module with thermostat_setpoint_get sent by association 5
8 (bit 3) setpoint is grabbed from external battery powered room sensor declared in parameter 122.
10 (bit 1 and bit 3) temperature AND setpoint are grabbed from external battery powered room sensor declared in parameter 122

Parameter 122: Node ID of external battery powered room sensor

If digital temperature sensor is not connected, module can grab measured temperature from external battery powered room sensor defined by this parameter.
NOTE: Get sensor node_id from controller and set parameter 122 immediately after sensor weak up (after button press on it etc.)

Size: 1 Byte, Default Value: 0

Setting Description
0 external battery powered room sensor not in function
1 - 254 Node ID of external battery powered room sensor

Technical Data

Dimensions 0.0700000x0.0700000x0.0200000 mm
Weight 49.75 gr
Hardware Platform ZM5202
EAN 3830062070133
IP Class IP 20
Voltage 230 V
Load 2300 W
Firmware Version 03.01
Z-Wave Version 04.05
Z-Wave Product Id 0x0159.0x0005.0x0051
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeZ-Wave Device