Oomi
Plug
SKU: FT096-A02
Quickstart
This is a
Turn the primary controller of Z-Wave network into inclusion mode, short press the products Action button that you can find on the product's housing.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Oomi Plug is a low-cost Z-Wave Switch plug-in module specifically used to enable Z-Wave command and control (on/off) of any plug-in tool. It can report immediate wattage consumption or kWh energy usage over a period of time. In the event of power failure, non-volatile memory retains all programmed information relating to the units operating status.Its surface has a Smart RGB LED, which can be used for indicating the output load status or strength of the wireless signal. You can configure its indication colour according to your favour.The Plug is also a security Z-wave device and supports Over The Air (OTA) feature for the products firmware upgrade.
| Reset to factory default | Press and hold the Action button that you can find on the product's housing for 20 seconds and then release. This procedure should only be used when the primary controller is inoperable. |
| Inclusion | Turn the primary controller of Z-Wave network into inclusion mode, short press the products Action button that you can find on the product's housing. |
| Exclusion | Turn the primary controller of Z-Wave network into exclusion mode, short press the products Action button that you can find on the product's housing. |
| NIF | XXXNIF |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Group 1 is assigned to the Lifeline association group and every device has 5 nodes to associate.When the switch is turned on or off using the action button, the switch will send a basic report of its status to the nodes in association group 1. To change what kind of signal is sent to the nodes in group 1, please see the detailed description of configuration parameter 80. |
| 2 | 5 | When the product receives a controlling Basic Set CC/Switch Binary Set CC, which if cause the products load state to be changed, which will lead to send the Basic Set CC/Switch Binary Set CC to nodes in group 2. |
Configuration Parameters
Parameter 101: To set which report need to be sent.
This parameter is used to configure which reports need to be sent in Report Group 1.The values corresponding to the first four bits of the parameter value may be combined to create different combinations of reports that you wish to have sent.For example, instantaneous Current is the value 2 and instantaneous Watts is the value 4, so setting parameter 101 to a value of 6 will result in both instantaneous Current and instantaneous Watts to be reported.See the full description of the parameter values for other possible settings. Size: 4 Byte, Default Value: 4
| Setting | Description |
|---|---|
| 8 | Report Accumulated kWh |
| 2 | Report Instantaneous Current (Amperes) |
| 4 | Report Instantaneous Watts |
| 1 | Report Instantaneous Voltage |
Parameter 102: To set which report need to be sent.
This parameter is used to configure which reports need to be sent in Report Group 2.The values corresponding to the first four bits of the parameter value may be combined to create different combinations of reports that you wish to have sent.For example, instantaneous Current is the value 2 and instantaneous Watts is the value 4, so setting parameter 102 to a value of 6 will result in both instantaneous Current and instantaneous Watts to be reported.See the full description of the parameter values for other possible settings. Size: 4 Byte, Default Value: 8
| Setting | Description |
|---|---|
| 1 | Report Instantaneous Voltage |
| 4 | Report Instantaneous Watts |
| 8 | Report Accumulated kWh |
| 2 | Report Instantaneous Current (Amperes) |
Parameter 103: To set which report need to be sent.
This parameter is used to configure which reports need to be sent in Report Group 3.The values corresponding to the first four bits of the parameter value may be combined to create different combinations of reports that you wish to have sent.For example, instantaneous Current is the value 2 and instantaneous Watts is the value 4, so setting parameter 103 to a value of 6 will result in both instantaneous Current and instantaneous Watts to be reported.See the full description of the parameter values for other possible settings. Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 4 | Report Instantaneous Watts |
| 8 | Report Accumulated kWh |
| 1 | Report Instantaneous Voltage |
| 2 | Report Instantaneous Current (Amperes) |
Parameter 111: Set the interval time of sending report.
This parameter is used to set the interval time of sending report in Report Group 1. (The unit of time is second). Size: 4 Byte, Default Value: 600
| Setting | Description |
|---|---|
| 0 - 268435456 | Interval Seconds |
Parameter 112: Set the interval time of sending report.
This parameter is used to set the interval time of sending report in Report Group 2. (The unit of time is second). Size: 4 Byte, Default Value: 600
| Setting | Description |
|---|---|
| 0 - 268435456 | Interval Seconds |
Parameter 113: Set the interval time of sending report.
This parameter is used to set the interval time of sending report in Report Group 3. (The unit of time is second). Size: 4 Byte, Default Value: 600
| Setting | Description |
|---|---|
| 0 - 268435456 | Interval Seconds |
Parameter 20: Configure the output load status after re-power on
Configure the output load status after re-power on the Smart Switch. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | The output load status will be the same as the previous state before a power outage. |
| 1 | The output load status will be ON state after re-power on. |
| 2 | The output load status will be OFF state after re-power on. |
Parameter 200: Partner ID
This parameter is used to configure the partner ID. (0== Aeon Labs Standard Product, 1~255== others). Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Aeon Labs Standard Product |
| 1 - 255 | Partner ID of Partner Product |
Parameter 252: Enable/Disable Lock Configuration
This parameter is used to enable/disable Lock all configuration parameters.(0 =disable, 1 = enable) Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | All configuration parameters are configurable. |
| 1 | All configuration parameters are not configurable (Locked). |
Parameter 254: Device Tag
This parameter is used to save the device tag, which will be written/ assigned in factory/ manufacturer. Size: 2 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 32767 | Device Tag |
Parameter 255: Reset to default factory setting
This parameter is used to reset product to default factory setting. (There are just 2 values can be used). Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1431655765 | Reset the product to default factory setting and be excluded from the Z-wave network. |
| 1 | Resets all configuration parameters to default setting. |
Parameter 3: Current Overload Protection
This parameter is used for the overload protection, which means the load will be disconnected after 2 minutes when the current more than 15.5A. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 | Overload Protection Disabled |
| 1 | Overload Protection is Enabled |
Parameter 33: Change the color value of RGB LED for testing
This parameter is only used for customer checking/testing the product's RGB color via changing the RGB values. Size: 4 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 0 - 255 | Reserved |
| 255 - 65535 | Range of red color value. |
| 65536 - 16777215 | Range of green color value. |
| 16777215 - 2147483647 | Range of blue color value. |
Parameter 80: Enable/Disable to send notifications to associated devices to associated devices.
This parameter is used to Enable/Disable to send notifications to associated devices (in Group 1) when the state of Smart Switch Gen5s load is changed. (0=Send nothing, 1=Send hail CC, 2=Send basic report CC). Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 2 | Send BASIC Report Command |
| 0 | Send Nothing (Disabled) |
| 1 | Send HAIL Command |
Parameter 81: Configure the state of LED
This parameter is used to configure the LED state when the Smart Switch is in Energy mode/Momentary indicate mode/Night light mode. Size: 1 Byte, Default Value: 0
| Setting | Description |
|---|---|
| 1 | The state of LED will follow with the output load state, but will turn off after 5 seconds if there is no any switch action.(Momentary indicate mode) |
| 2 | The state of LED will the same with Night light mode state configured by parameter 83. |
| 0 | The state of LED will follow with the output load state(Energy mode) |
Parameter 83: Configure the LED indication status when it is in Night light mode
This parameter is used to configure the LED indication status when the current mode is Night light mode. Size: 4 Byte, Default Value: 14524637
| Setting | Description |
|---|---|
| 0 - 255 | Set the indication value of red Led. |
| 256 - 65535 | Set the indication value of green Led. |
| 65536 - 16777215 | Set the indication value of blue Led. |
Parameter 84: Configure the brightness level for the LED indication
This parameter is used to configure the brightness level for the LED indication.Brightness level range is 0 to 100%. Size: 1 Byte, Default Value: 50
| Setting | Description |
|---|---|
| 0 - 100 | Brightness level range is 0 to 100%. |
Parameter 90: Enable/Disable the function of parameter 91 and 92.
This parameter is used to Enable/Disable the function of parameter 91 and 92 (1=Enabled, 0=Disabled). Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Configuration Parameters 91 and 92 are Disabled |
| 1 | Configuration Parameters 91 and 92 are Enabled |
Parameter 91: Induce an automatic report
This parameter is used to induce an automatic report when the change of the current power is more/less than the threshold in wattage. Size: 2 Byte, Default Value: 25
| Setting | Description |
|---|---|
| 0 - 32767 | The threshold can be set from 0 to 32767 watt. |
Parameter 92: Induce an automatic report
This parameter is used to induce an automatic report when the change of the current power is more/less than the threshold in percentage. Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 - 100 | The threshold can be set from 0 to 100 percent. |
Technical Data
| Hardware Platform | ZM5101 |
| Device Type | On/Off Power Switch |
| Network Operation | Always On Slave |
| Firmware Version | HW: 60 FW: 1.02 |
| Z-Wave Version | 6.51.06 |
| Certification ID | ZC10-15110005 |
| Z-Wave Product Id | 0x016A.0x0103.0x0060 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |