This is a
Inclusion, Exclusion and Wake Up are confirmed by triple clicking the B-Button inside the case.
The Fibaro Motion Sensor is a universal Z-Wave multi-sensor. Along with detecting motion the device measures the temperature and light intensity. The sensor has a built-in accelerometer to detect any tampering of the device. The Fibaro Motion Sensor is battery powered device and designed to be installed qickly and easily on any surface. The LED indicator signals motion, temperature level, operating mode and can be used to see if device is within the Z-Wave network. The motion sensor can be used for lighting scenes and security monitoring systems.
INSTALLATION POSITION
Fibaro Motion Sensor has to be installed in a corner of the room or perpendicularly to the doors. Actual range of the sensor can be influenced by environment conditions. Should false motion alarms be reported, check for any moving objects within the sensor"s detection area, such as trees blowing in the wind, cars passing by, windmills. False motion alarms may be caused by moving masses of air and heat as well. If the device keeps on reporting false alarms, despite eliminating all of the above-mentioned factors, install the device in another place.
SENSOR INSTALLATION
Note: Fibaro Motion Sensor cannot be pointed at any source of heat (e.g.radiators, fireplaces, cookers, etc.) or at any source of light (direct sunlight, lamps). It"s not recommended to install the motion sensor in places prone to drafts. Sensor can be mounted using screw or the sticker.
Fibaro Flood Sensor has four sensors built in - Motion Sensor, Temperature Sensor, Light Sensor and Accelerometer.
It is compatible with any Z-Wave controller. The sensors detect motion using a passive IR sensor, measures the temperature and measures the light intensity. It is easy to install on a wall or any surface. It is protected against tampering and theft - once vibrations are detected, the notification is sent to the main controller. The alarms of movement and temperature are signaled by blinking of LED diode. The accelerometer has also a simple earthquake detector mode.
By using association with Fibaro"s devices the Fibaro Motion Sensor may control another Z-Wave network device, e.g. a Dimmer, Relay Switch, Roller Shutter, RGBW Controller, Wall Plug, or a scene. Fibaro Motion Sensor allows for the association of three groups. The Fibaro Motion Sensor allows for controlling 5 regular and 5 multichannel devices per an association group, out of which 1 field is reserved for the Z-Wave network main controller.
EARTHQUAKE DETECTOR MODE
Fibaro Motion Sensor can be configured to work as a simple earthquake detector, by setting the Parameter 24 value to 4. Reports with scale of the vibrations (dimensionless) will be sent at the time intervals specified in Parameter 22. First report will be sent immediately after vibrations have been detected. The minimum value of the vibrations, resulting in report being sent, can be defined in Parameter 20. Once the vibrations cease, reports will stop being sent.
Z-Wave Range Test
Fibaro Multi Sensor has a built in Z-Wave network range test for the main controller. Follow the instruction to test the main controller"s range:
Z-Wave Range Tester signaling modes:
LED Indicator pulsing green - Fibaro Motion Sensor attempts to extablish a direct communication with the main controller. If a direct communication attempt fails, sensor will try to establish a routed communication, through other modules, which will be signaled by LED indicator pulsing yellow.
LED Indicator glowing green - Fibaro Motion Sensor communicates with the main controller directly.
LED Indicator pulsing yellow - Fibaro Motion Sensor tries to establish a routed communication with the main controller through other modules (repeaters).
LED Indicator glowing yellow - Fibaro Motion Sensor communicates with the main controller through the other modules. After 2 seconds the sensor will retry to establish a direct communication with the main controller, which will be signaled with LED blinking in green.
LED Indicator pulsing violet - Fibaro Motion Sensor does communicate at the maximum distance of the Z-Wave network. If connection proves successful it will be confirmed with a yellow glow. It"s not recommended to use the sensor at the range limit.
LED Indicator glowing red - Fibaro Motion Sensor is not able to connect to the main controller directly or through another Z-Wave network device (repeater).
Reset to factory default | The Fibaro Motion Sensor reset erases the EPROM memory, including all information on the Z-Wave network and the main controller. Fibaro Motion Sensor"s reset procedure: 1. Make sure the battery works and is in place. 2. Press and hold the B-button for 4-6 seconds until the LED glows signaling the 2nd menu level. 3. Release the B-button. 4. Again, press the B-button briefly. 5. Successful reset will be confirmed with the LED changing colour to red and fading. |
Inclusion | Make sure that your Z-Wave Controller is in the Inclusion-/Exclusion-Mode. Tripple click the Z-Wave button inside the case to confirm the process. |
Exclusion | Make sure that your Z-Wave Controller is in the Inclusion-/Exclusion-Mode. Tripple click the Z-Wave button inside the case to confirm the process. |
NIF | Tripple click on the B-button inside the case or a detection by one of the sensors will send a Node Information Frame. |
Wakeup | Tripple click on the B-button inside the case will wake up the device. |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
3 | 1 | reports the device status and allows for assigning a single device only (the main controller by default - the device reports its status to the main controller). Itu2019s not recommended to modify this association group. |
2 | 5 | is assigned to the tamper alarm. Alarm frame will be sent to the associated devices once tampering is detected. |
1 | 5 | is assigned to the device status - sending, the BASIC SET control frame to the associated devices having detected motion. |
The lower the value, the more sensitive the PIR sensor. Size: 1 Byte, Default Value: 0a
Setting | Description |
---|
Period of time through which the PIR sensor is u201cblindu201d (insensitive) to motion. After this time period the PIR sensor will be again able to detect motion. Size: 1 Byte, Default Value: 0f
Setting | Description |
---|
Sets the number of moves required for the PIR sensor to report motion. The lower the value, the less sensitive the PIR sensor. Itu2019s not recommended to modify this parameter settings. Size: 1 Byte, Default Value: 01
Setting | Description |
---|
Period of time during which the number of moves set in parameter 3 must be detected in order for the PIR sensor to report motion. The higher the value, the more sensitive the PIR sensor. Itu2019s not recommended to modify this parameter setting. Size: 1 Byte, Default Value: 02
Setting | Description |
---|
Period of time, after the motion alarm will be cancelled in the main controller and the associated devices. Any motion detected during the cancellation delay time countdown will result in the countdown being restarted. In case of small values, below 10 seconds, the value of parameter 2 must be modified (PIR sensoru2019s u201cBlind Timeu201d). Size: 2 Byte, Default Value: 001e
Setting | Description |
---|
determines the part of day in which the PIR sensor will be active. parameter influences only the motion reports and associations. Tamper, light intensity and temperature measurements will not be influenced. Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
00 | PIR sensor always active |
01 | PIR sensor active during the day only |
02 | PIR sensor active during the night only |
parameter defines the difference between night and day, in terms of light intensity, used in parameter 8. Size: 2 Byte, Default Value: 00c8
Setting | Description |
---|
parameter determines the command frames sent in 1-st association group, assigned to PIR sensor. Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
00 | BASIC ON and BASIC OFF command frames sent in Basic Command Class. |
01 | only the BASIC ON command frame sent in Basic Command Class. |
value of 255 allows to turn ON a device. In case of the Dimmer, the value of 255 means turning ON at the last memorized state. Size: 1 Byte, Default Value: ff
Setting | Description |
---|---|
ff | ON |
00 | OFF |
01 - 63 | % |
command frame sent at the moment of motion alarm cancellation, after the cancellation delay time, specified in parameter 6, has passed. Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
ff | ON |
00 | OFF |
01 - 63 | % |
parameter determines the chages in forces acting on the Motion Sensor resulting in tamper alarm beig reported - g-force acceleration. Size: 1 Byte, Default Value: 0f
Setting | Description |
---|
Time period after which a tamper alarm will be cacelled. Another tampering detected durig the countdown will NOT extend the delay. Size: 2 Byte, Default Value: 001e
Setting | Description |
---|
parameter determines the behaviour of tamper and how it reports. Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
00 | Tamper alarm is reported in Sensor Alarm command class / Cancellation is not reported. |
01 | Tamper alarm is reported in Sensor Alarm command class / Cancellation is reported in Sensor Alarm commad class after the time period set in parameter 22 (Tamper Alarm Cancellation Delay) |
02 | Tamper alarm is reported in Sensor Alarm command class / Cancellation is not reported. Sensoru2019s orientation in space is reported in Fibar Commad Class after the time period set in paramer 22. |
03 | Tamper alarm is reported in Sensor Alarm command class / Cancellation is reported in Sensor Alarm commad class after the time period set in parameter 22. Sensoru2019s orientation in space is reported in Fibar Commad Class after the time period set in paramer 22. |
04 | The maximum level of vibrations recorded in the time period set in parameter 22 is reported. Reports stop being sent when the vibrations cease. The reports are sent in Sensor Alarm command class. Value displayed in the u201cvalueu201d field (0 - 100) depends on the vibrations force. Reports to the association groups are sent using Sensor Alarm command class. |
parameter determines whether the tamper alarm frame will or will not be sent in broadcast mode. Alarm frames sent in broadcast mode may be received by all of the devices within communication range. Size: 1 Byte, Default Value: 00
Setting | Description |
---|---|
00 | Tamper alarm is not sent in broadcast mode. |
01 | Tamper alarm sent in broadcast mode. |
parameter determines the change in light intensity level resulting in illumination report being sent to the main controller. Size: 2 Byte, Default Value: 00c8
Setting | Description |
---|
Time interval between consecutive illumination reports. Size: 2 Byte, Default Value: 0000
Setting | Description |
---|
parameter determines the change in level of temperature resulting in temperature report. Size: 1 Byte, Default Value: 0a
Setting | Description |
---|
parameter determines how often the temperature will be measured. Size: 2 Byte, Default Value: 0384
Setting | Description |
---|
parameter determines how often the temperature reports will be sent. Size: 2 Byte, Default Value: 0000
Setting | Description |
---|
value to be added to the actual temperature, measured by the sensor (temperature compensation). Size: 2 Byte, Default Value: 0000
Setting | Description |
---|
parameter determines the way in which LED diode behaves after motion has been detected Size: 1 Byte, Default Value: 0a
Setting | Description |
---|---|
00 | LED inactive. |
01 | LED colour depends on the temperature. Set by parameters 86 and 87. |
02 | Flashlight mode - LED glows in white for 10 seconds. |
03 | White. |
04 | Red |
05 | Green |
06 | Blue |
07 | Yellow |
08 | Cyan |
09 | Magenta |
0a | LED colour depends on the temperature. Set by parameters 86 and 87. |
0b | Flashlight mode - LED glows in white through 10 seconds. |
0c | White |
0d | Red |
0e | Green |
0f | Blue |
10 | Yellow |
11 | Cyan |
12 | Magenta |
13 | LED colour depends on the temperature. Set by parameters 86 and 87. |
14 | White |
15 | Red |
16 | Green |
17 | Blue |
18 | Yellow |
19 | Cyan |
1a | Magenta |
parameter determines the brightness of LED when indicating motion. Size: 1 Byte, Default Value: 32
Setting | Description |
---|
ambient illumination level below which LED brightness is set to 1%. parameter is relevant only when the parameter 81 is set to 0. Size: 2 Byte, Default Value: 0064
Setting | Description |
---|
ambient illumination level above which LED brightness is set to 100%. parameter is relevant only when the parameter 81 is set to 0. Size: 2 Byte, Default Value: 03e8
Setting | Description |
---|
Minimum temperatur resulting in blue LED illumination. parameter is relevant only when parameter 80 has been properly configured. Size: 1 Byte, Default Value: 12
Setting | Description |
---|
Maximum temperatur resulting in red LED illumination. parameter is relevant only when parameter 80 has been properly configured. Size: 1 Byte, Default Value: 1c
Setting | Description |
---|
Indicating mode resembles a police car (white, red and blue). Size: 1 Byte, Default Value: 01
Setting | Description |
---|---|
00 | LED does not indicate tamper alarm. |
01 | LED indicates tamper alarm. |
Dimensions | 0.0470000x0.0470000x0.0470000 mm |
Weight | 24 gr |
EAN | 5902020528258 |
Battery Type | 1 * CR123 |
Device Type | Routing Binary Sensor |
Generic Device Class | Binary Sensor |
Specific Device Class | Routing Binary Sensor |
Firmware Version | 02.04 |
Z-Wave Version | 03.43 |
Certification ID | ZC08-14060005 |
Z-Wave Product Id | 010f.0800.1001 |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |