This is a
1) Open the cover by turning it counter-clockwise.2) Remove battery blocker.3) Place the device within the direct range of your Z-Wave controller.4) Set the main controller in (security/non-security) add mode (see the controllers manual).5) Quickly, triple click the TMP button located inside the casing.6) Wait for the adding process to end. 7) Successful adding will be confirmed by the Z-Wave controllers message.8) Close the cover by turning it clockwise.9) Place the sensor onto a surface prone to flooding. Three electrodes underneath the device should evenly touch the surface.
FIBARO Flood Sensor is a universal, Z-Wave Plus compatible, flood and temperature sensor. The device can be powered using battery, 12/24V DC power supply or both. Flood alarm is sent to the Z-Wave network devices or additionally to any alarm system controller through opening a NC contact using the external power supply. The device has a built-in temperature sensor that allows to monitor ambient temperature. FIBARO Flood Sensor is designed to be placed on the floor or mounted on a wall (in this case Flood Sensor probes should be extended using addition wire). The device has a built-in visual LED indicator and an acoustic alarm. The LED indicator signals flood, operating mode or the Z-Wave network communication range. In addition, the device is equipped with a sensor reporting tilt or movement to the main controller e.g. when someone has taken the Sensor from its original location.FIBARO Flood Sensor is sink-proof, which means it drifts on the water surface and keeps on sending alarm signal in case of substantial inundation of water (if not wired). Flood Sensor is compatible with any Z-Wave or Z-Wave+ Controller.
Reset to factory default | 1) Open the cover by turning it counter-clockwise. 2) Make sure the device is powered (either by a battery or a DC power supply).3) Press and hold the TMP button for 15-20 seconds until LED glows yellow (4th menu position).4) Release and click the TMP button to start the reset procedure.5) Successful reset will be confirmed with the LED indicator changing colour to red and an acoustic signal.Use reset procedure only if the primary controller is missing or inoperable. |
Inclusion | 1) Open the cover by turning it counter-clockwise.2) Remove battery blocker.3) Place the device within the direct range of your Z-Wave controller.4) Set the main controller in (security/non-security) add mode (see the controllers manual).5) Quickly, triple click the TMP button located inside the casing.6) Wait for the adding process to end. 7) Successful adding will be confirmed by the Z-Wave controllers message.8) Close the cover by turning it clockwise.9) Place the sensor onto a surface prone to flooding. Three electrodes underneath the device should evenly touch the surface. |
Exclusion | 1) Open the cover by turning it counter-clockwise.2) Make sure the device is powered (either by a battery or a DC power supply).3) Place the device within the direct range of your Z-Wave controller.4) Set the main controller in remove mode (see the controllers manual).5) Quickly, triple click the TMP button located inside the casing.6) Wait for the removing process to end.7) Successful removing will be confirmed by the Z-Wave controllers message. |
NIF | XXXNIF |
Wakeup | FIBARO Flood Sensor will wake up at a defined time interval and will always try to communicate with the main controller. There is a possibility to wake up the device manually by clicking the TMP button |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | Lifeline reports the device status and allows for assigning single device only (main controller by default). |
2 | 5 | Flood Control devices in this group will be switched on or off when flood status changes (done via BASIC SET command frames). |
3 | 5 | Flood Alarm is assigned to the device status - devices in this group will receive notification about flood detection or cancellation. Useful for devices that can trigger alarms. |
4 | 5 | Tamper Alarm is assigned to the TMP button and tilt sensor - devices in this group will receive a notification when the sensor is moved or the cover is taken off (which normally holds the button). Useful for devices that can trigger alarms. Functionality can be altered by parameter 74. |
Determines time period (in seconds) by which a Flood Sensor will retainthe flood state after the flooding itself has ceased. The sensorwill keep on reporting flooding to the main controller. This parametersetting does not affect acoustic and visual alarms, which turn off immediatelyafter flooding ceases. Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
0 - 3600 | (in seconds, each 1s) |
Time interval (in seconds) between consecutive measurements ofbattery level and temperature (done by built-in temperature sensor).If the temperature differs from previously reported by a value determinedin parameter 12, it will be reported to the Z-Wave controller.In battery mode more significant battery level changes will be reported.Short time intervals mean more frequent communication, whichresults in shortened battery life.After consecutive FAILED and SUCCESSFUL communication attempts,the Sensor will go to standby mode. Size: 4 Byte, Default Value: 300
Setting | Description |
---|---|
1 - 65535 | in seconds |
Determines a minimum temperature change value (insensitivity level),resulting in a temperature report being sent to the main controller, according to the parameter 10 settings. Size: 2 Byte, Default Value: 50
Setting | Description |
---|---|
1 - 1000 | each 0.01C |
The parameter allows for deactivation visual and acoustic alarm.Parameter allows for increasing a battery life. Setting changes will notaffect the sensors communication with the main controller - commandsto association groups, alarms and reports will still be sent. Size: 1 Byte, Default Value: 3
Setting | Description |
---|---|
0 | acoustic and visual alarms inactive |
1 | acoustic alarm inactive, visual alarm active |
2 | acoustic alarm active, visual alarm inactive |
3 | acoustic and visual alarms active |
The parameter stores a temperature value, below which visual indicatorblinks with a colour determined by a parameter 61 settings. Bydefault the visual indicator blinks blue. Size: 2 Byte, Default Value: 1500
Setting | Description |
---|---|
-10000 - 10000 | each 0.01C |
The parameter stores a temperature value, above which visual indicatorblinks with a colour determined by the parameter 62 settings. Bydefault the visual indicator blinks red. Size: 2 Byte, Default Value: 3500
Setting | Description |
---|---|
-10000 - 10000 | each 0.01C |
Parameter stores RGB colour value (see the note below for details). Size: 4 Byte, Default Value: 255
Setting | Description |
---|---|
0 - 16777215 | Red 16711680; Green 65280; Blue 255; Yellow 16776960; Turquoise 65535; Orange 16750848; White 16777215; Indicator turned off 0 |
Parameter stores RGB colour value (see the note below for details).NOTEThe main controller interprets colours as a sum of its component colours value. Each colours value is a number from 0 to 255.Indicated colour = 65536RED + 256GREEN + BLUEColourDecimal value Red16711680Green 65280Blue255Yellow16776960Turquoise65535Orange16750848White16777215Indicator turned off 0 Size: 4 Byte, Default Value: 16711680
Setting | Description |
---|---|
0 - 16777215 | Red 16711680; Green 65280; Blue 255; Yellow 16776960; Turquoise 65535; Orange 16750848; White 16777215; Indicator turned off 0 |
Parameter determines visual indicators operation. Setting to 0 turnsthe temperature LED indication off, saving battery life. Size: 1 Byte, Default Value: 2
Setting | Description |
---|---|
0 | visual indicator does not indicate the temperature |
1 | visual indicator indicates the temperature (blink) every Temperature Measurement Interval (parameter 10, constant current and battery) and Wake Up Interval (battery mode) |
2 | visual indicator indicates the temperature continuously, only in constant power mode |
Determines the requested on level to be sent to devices from 2ndassociation group upon flood event. Size: 2 Byte, Default Value: 255
Setting | Description |
---|---|
1 - 99 | requested level |
255 | turn a device on |
Parameter stores a temperature value to be added to or deductedfrom the current temperature measured by internal temperature sensorin order to compensate the difference between air temperatureand temperature at the floor level. Size: 2 Byte, Default Value: 0
Setting | Description |
---|---|
-10000 - 10000 | 0.00 |
(MOVEMENT_TAMPER / BUTTON_TAMPER)The device is able to report tamper alarms resulting from sensors tilt/movement or TMP button state change (e.g. taking off the top cover). Size: 1 Byte, Default Value: 2
Setting | Description |
---|---|
0 | tamper alarms inactive |
1 | button tamper alarm active |
2 | movement tamper alarm active |
3 | button and movement tampers alarm active |
The device is capable of automatically turning off alarm signalizationafter a certain amount of time. Long lasting alarm may reduce batterlife, when constantly signalized.The parameter determines time after which alarm will become quiet- still active but the device will go into battery saving mode. Visual oracoustic alarm will be reactivated after time specified in the parameter76. When alarm status ceases, alarm will be turned off immediately.NOTEParameter 75 is ignored when parameter 2 is set to 0. Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
0 | alarms active indefinitely |
1 - 65535 | time in seconds |
Parameter determines a time period after which an alarm will be turnedback on (in case it was turned off by parameter 75 setting). It will alsoresend commands to 2nd and 3rd association groups as if the alarmwas detected again.NOTEIn case a time period set in parameter 76 is shorter than the one specified in parameter75, the device will not quiet the alarm, it will remain active. Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
0 | alarm reactivation inactive |
1 - 65535 | time in seconds |
Allows to turn off the internal flood sensor. Tamper and built in temperaturesensor will remain active. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Default flood sensor operation (flood detection, reactions) |
1 | Built-in flood sensor TURNED OFF (does not change its state in the main controller, does not send alarm notifications nor turn on/off commands to 2nd/3rd association groups with flood state changes. Always visible in the main controller as turned off) |
This parameter defines how commands are sent in specified associationgroups: as secure or non-secure. Parameter is active only in Z-Wavenetwork security mode. It does not apply to 1st Lifeline group. Size: 1 Byte, Default Value: 7
Setting | Description |
---|---|
0 | acoustic and visual alarms inactive |
0 | none of the groups sent as secure |
1 | 2nd group, Control, sent as secure |
1 | acoustic alarm inactive, visual alarm active |
2 | acoustic alarm active, visual alarm inactive |
2 | 3rd group, Alarm, sent as secure |
3 | acoustic and visual alarms active |
4 | 4th group, Tamper, sent as secure |
This setting decides whether device turn off commands and alarmcancellation notifications will be sent to devices in 2nd and 3rd associationgroups (respectively)Setting the parameters value to 0 disables sending these two commandsto associated devices. This means that these devices WILL NOTbe informed when the flooding has ceased. It is still possible to cancelalarms in 3rd association group by choosing second (green) menuposition (see Menu & visual indications on page 10). Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | alarm (flooding) cancellation inactive |
1 | alarm (flooding) cancellation active |
Hardware Platform | ZM5202 |
Device Type | Notification Sensor |
Network Operation | Reporting Sleeping Slave |
Firmware Version | HW: 1 FW: 3.03:03.03 |
Z-Wave Version | 6.51.07 |
Certification ID | ZC10-18015962 |
Z-Wave Product Id | 0x010F.0x0B01.0x2002 |
Supported Notification Types | Water Alarm |
Color | White |
Firmware Updatable | Updatable by Consumer by RF |
Sensors | Air Temperature |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |