Quickstart

This is a Multiposition Motor Switch for XXXQFrequencyName. To run this device please connect it to your mains power supply.

Triple click one of the buttons on the device will include the device. A green blinking of LED will indicate successful inclusion. The device is excluded by triple click to one of the buttons.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

The Duwi Flush Mountable Motor Control is a wireless actuator able to control 230 V powered motors for blinds and jalousies. The device is delivered as a complete set with flush mountable insert, paddle and mounting frame compatible to the design of the switching series DURO 2000 SI in color pearl white from Busch Jaeger. The paddle of the device is used to control the device itself . The status of the motor control is indicated on a dual color LED for test purposes. This device is designed for a 3 wire system and needs a neutral wire in the wall box.

Installation

The insert is designed to fit into standard circular European wall boxes with 60 mm diameter. The insert combined with the mounting plate can be screwed in top of the wall box using the two screws delivered with the device. The mounting frame is then attached to the mounting plate and the switch is completed by pushing the switching paddle into the mounting frame. Mind the arrow on the inserts top side showing the mounting direction of the insert. It is also possible to mount the insert without any local operation behind a cover or inside a lamp. The mounting plate, frame and the switching paddle become useless in such a scenario.

The schematics below shows how to wire the actuator. The hot wired from the mains distribution panel is connected to the inserts contacts L. The contact S is the switched contact and need to be connected to the cable to the load. The cable from the load is connected to neutral N. If there are both neutral and hot wire in the wall box the neutral from the mains panel and the neutral to the lamp need to be connected. It is not harmful if the two connections L and S are mismatched on the actuator.

A fuse protects the electronics of the actuator. The fuse is accessible on the top side of the device. Inside the plug there is the working fuse plus a spare fuse.

CALIBRATION:

The device is able to position a blind on a desired percentage position (50 percent open) when controlled wirelessly. To allow this kind of positioning the total travel times of the motor in opening and closing direction must be determined using the following process:

  1. Move the blind into the upper end position.
  2. Push "UP" and "DOWN" for two seconds until LED blinks green. (Remark: Paddle need to be removed in order to push both buttons in parallel)
  3. Move the blind into the other end position using the UP and DOWN buttons. The LED will blink faster.
  4. Once the buttons are released at the end position this position is saved and confirmed by 3 sec green LED

Product Usage

The actuator is operated by the local switching paddles or wirelessly using Z-Wave commands (communication patterns 1, 4, 5 and 7). If the insert is mounted correctly pushing the upper part of the paddle will turn on the load; pushing the lower part of the paddle will turn the blind into the close position, pushing the upper part of the paddle will turn the blind into the open position. Hitting the paddle during operation (moving motor) will stop the operation for safety reasons. Keeping the paddle pushed moved the motor until the desired position is reached. Relasing the paddle will stop the motor.

The device is also able to remotely operate other devices (communication pattern 5) by sending wireless Z-Wave commands.

Reset to factory default XXXResetDescription
Inclusion

Blinking red/green LED indicates that the device is in factory reset state. Once the controller is turned into inclusion mode triple click one of the buttons on the device will include the device. A green blinking of LED will indicate successful inclusion that will be turned off shortly afterwards. The device is excluded by triple click to one of the buttons when the controller is in exclusion mode.

Exclusion

Blinking red/green LED indicates that the device is in factory reset state. Once the controller is turned into inclusion mode triple click one of the buttons on the device will include the device. A green blinking of LED will indicate successful inclusion that will be turned off shortly afterwards. The device is excluded by triple click to one of the buttons when the controller is in exclusion mode.

NIF XXXNIF
Wakeup XXXWakeupDescription
Protection XXXProtection
FirmwareUpdate XXXFirmwareUpdate
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 Basic On/Off Group

Technical Data

Dimensions 0.0080000x0.0080000x0.0050000 mm
Weight 100 gr
Hardware Platform ZM3102
IP Class IP 20
Voltage 230
Load 2 * 1500 W
Device Type Window Covering No Position/Endpoint
Generic Device Class Multilevel Switch
Specific Device Class Multiposition Motor Switch
Firmware Version 01.00
Z-Wave Version 02.33
Certification ID ZC08-08100017
Z-Wave Product Id 0064.4001.0000
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeWindow Covering No Position/Endpoint