Devolo
Z-Wave Room Sensor
SKU: DEVE9361
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
Z-Wave RS is a battery operated temperature sensor. When included into Z-Wave wireless network, its buttons can also be used to control the heating system.
Installation
Product Usage
| Reset to factory default |  |
| Inclusion | Press the LED button on the Z-Wave RS. |
| Exclusion | Hold down the 3 buttons on the Z-Wave RS for 5 seconds (up, down and LED buttons). |
| NIF | Each time the LED button is pressed the Z-Wave RS will and send NIF. This is also true when the Z-Wave RS is in tamper-proof mode. |
| Wakeup | A controller can only communicate with the Z-Wave RS when it is awake. The intervals when the Z-Wave RS is awake can be set using the WakeUp Command Class. By default the WakeUp interval is 60 minutes. The Z-Wave RS can be woken manually by pushing any of the three buttons, and will stay awake for 10 seconds. |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 1 | Lifeline |
Configuration Parameters
Parameter 1: Temperature Report threshold
Size: 2 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 1 - 100 | 0.1 to 10°C |
Parameter 2: Set-point display resolution
Size: 2 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 1 - 100 | From 0.1 to 10°C in 0.1°C steps |
Parameter 3: Min set-point and override limit
Size: 2 Byte, Default Value: 12
| Setting | Description |
|---|---|
| 0 - 40 | From min 0°C to max setpoint/override limit |
Parameter 4: Max set-point and override limit
Size: 2 Byte, Default Value: 28
| Setting | Description |
|---|---|
| 0 - 40 | From min setpoint/override limit to max 40°C |
Parameter 5: LED Flash period
Size: 2 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 - 65535 | seconds |
Parameter 6: Setpoint control function
Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Disabled |
| 1 | Enabled |
Parameter 7: Temporarily override scheduler
Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 0 | Disabled |
| 1 | Enabled |
Parameter 8: Setpoint Type in Thermostat_ Setpoint_Reports
Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 | Heating |
| 2 | Cooling |
| 10 | Auto Changeover |
Parameter 9: LED on time
Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 - 5 | 100 to 500ms in 100ms steps |
Parameter 10: Number of LED flashes (duration)
Size: 1 Byte, Default Value: 5
| Setting | Description |
|---|---|
| 0 - 255 | flashes |
Parameter 11: LED Color
Size: 1 Byte, Default Value: 1
| Setting | Description |
|---|---|
| 1 | Green |
| 2 | Red |
Technical Data
| Dimensions | 75x75x18 mm |
| Weight | 71 gr |
| Hardware Platform | ZM3102 |
| EAN | 4250059693616 |
| IP Class | IP 21 |
| Battery Type | 2 * AA 1,5V |
| Device Type | Central Controller |
| Generic Device Class | Multilevel Sensor |
| Specific Device Class | Routing Multilevel Sensor |
| Z-Wave Version | 4.55.00 |
| Certification ID | ZC08-14070002 |
| Z-Wave Product Id | 0x0002.0x0003.0x8010 |
| Frequency | Europe - 868,4 Mhz |
| Maximum transmission power | 5 mW |