Quickstart

This is a Z-Wave Device for Europe. To run this device please connect it to your mains power supply.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

The Keypad is the first Z-Wave enabled and outdoor Keypad in the Smart Home world!

The Keypad can activate and deactivate your security system by using an individual Pin Code. Furthermore you can unlock connected doorlocks without a key but with a multi-digit Code.

As soon as somebody logs in with his personal Pin Code you will be informed automatically. Because of that you even know while your on the road, when your kids arrived at home. Beside the Keypad does not need a key, which are often lost by kids. 

The POPP Keypad can save up to 20 different Pin Codes. Each Code can have 4-10 digits. Every single Pincode has its own scene ID and can start other scenes. Meanwhile you can also us the different scenes IDs to see, who and when one of the residents came home. Additionally the Keypad has an separated doorbell button, which controls his own scene. That way you can switch on a light and turn down the volume of your hifi system when somebody rings the door.

The Keypad is protected against tamper and burglar due to its integrated magnetic sensor. If the Keypad is moved unauthorized, you receive a push message (gateway mode) immediately or a siren will be triggered. In addition a separted scene ID is used, when a wrong Pin Code is entered. As a result you know directly when somebody use the keypad unauthorized. 

An integrated multicolor LED shows, if the Pin Code was entered correctly and informs if the entered Code was transmitted successfully. 

Stand alone and Gateway mode

The Keypad can be used in 2 different modes. Firstly it can be use in connection to a doorlock or dooropener in the Stand-Alone mode. For that you do not need a Z-Wave gateway because the Keypad is directly associated with the door opener.

Secondly the Keypad can be used in the Gateway mode. For that the keypad is connected to the Gateway and is shown as a scene controller. Each access code gets his own scene ID. The doorbell button and the wrong entering of code will be shown with own scene IDs.

Features:

We would like to point out that this article is not a new product. The product has got the complete functionality and can be integrated into a Z-Wave Smart Home without restriction.

However, the product may have the following characteristics:

We offer to you a guarantee of 1 year. With a possible return you receive a credit note, there is no exchange of the product.

The picture may not correspond to the scope of delivery of the product.

If you are interested in a larger quantity of used products, please contact your sales representative.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

  1. Make sure a device is in factory reset state before including. In doubt exclude before include.
  2. If inclusion still fails, check if both devices use the same frequency.
  3. Remove all dead devices from associations. Otherwise you will see severe delays.
  4. Never use sleeping battery devices without a central controller.
  5. Dont poll FLIRS devices.
  6. Make sure to have enough mains powered device to benefit from the meshing

Technical Data

Dimensions 0.0750000x0.1200000x0.0240000 mm
Weight 290.13 gr
Certification ID ZC10-17085733
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW

Explanation of Z-Wave specific terms