Popp
POPP Thermostatic Radiator Valve
SKU: B_POPE010101
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
Increase the comfort and save energy simultaneously. With the POPP thermostat, radiators will become important modules of your home automation. Intelligent connected to various sensors and individual heating schedules, you will only heat when it’s needed and only to your defined comfortable temperature. Additionally, the heating process will be stopped automatically, as soon as a window will be opened. Or you can activate the heating from outside, if you are on the way home earlier than expected.
The POPP radiator thermostat is mounted on wall heating valves and controls them by a motor. The device accepts a setpoint that is either set manually using local buttons on the device or wirelessly using Z-Wave. Beside setting a desired temperature the device will support special heating schemes, such as energy saving and frost protection. A small LCD panel on the device displays the set temperature. An internal temperature sensor measures the actual temperature and reports to the control center.
The thermostat also allows further intelligent functions such as detection of open windows with shift to energy saving mode or a valve training function to ensure that valves are still operational after longer periods.
The POPP thermostat can be mounted with few movements to valves with standard M30x1.5 connector or RA2000 (Danfoss snap in). The device expects a regular radio connection to the IP gateway for status message exchange.
Compared to Danfoss LC-13 thermostatic radiator valve, the Popp thermostat owns an integrated temperature sensor which reports measured temperature to the Z-Wave control center.
Features:
- Thermostat for water-based radiators
- Integrated temperature sensor
- Local control buttons
- LCD display (set temperature)
- For valves with standard M30x1.5 connector (30x1,5) or RA2000 (Danfoss snap in).
- Low-noise motor
- Child protection
- Explorer Frame Support
- Wireless technology: Z-Wave
- Dimensions: 51 x 51 x 71 mm
We would like to point out that this article is not a new product. The product has got the complete functionality and can be integrated into a Z-Wave Smart Home without restriction.
However, the product may have the following characteristics:
- broken seal,
- damaged packaging,
- no original packaging
- missing accessories,
- minimal signs of wear,
- no current software version.
We offer to you a guarantee of 1 year. With a possible return you receive a credit note, there is no exchange of the product.
The picture may not correspond to the scope of delivery of the product.
If you are interested in a larger quantity of used products, please contact your sales representative.
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| Dimensions | 0.0510000x0.0750000x0.0790000 mm |
| Weight | 110 gr |
| Frequency | Europe - 868,4 Mhz |
| Maximum transmission power | 5 mW |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.