This is a
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
frient Motion Sensor Pro - a 3 in 1 Sensor (motion, light and temperature). Imagine always having a frient looking after motion, light, and temperature in your and your loved ones" homes - all in one. You know, someone who texts you if something’s moving in the kitchen while you’re at work. Someone who can watch out for your elderly grandma who lives far away and alert you if something is wrong with her.
A secure home starts with a smart frient. The frient sensor is a smart home device that lets you detect movements, light, and temperature. The Motion Sensor Pro is designed to help you through the day in whatever way you need. It makes life easier when you are at home and more secure when you are away. Your new frient lets you know if there"s movement in your home when it shouldn"t be - allowing you to act fast and protect your home.
Keep an eye on your home and your loved ones. Want to turn on the lights, turn off the music, or adjust the thermostat? Your frient is right there to do it for you. Want to check up on a loved one who lives alone? The Zigbee-based Motion Sensor Pro also works as a healthcare monitor, tracking movements in your grandmother’s house and telling you if something isn’t right.
No more blind spots. Install your Motion Sensor Pro wherever it fits best and has a good view of your home. Your new smart home frient comes with different mounting options giving you maximum flexibility to place your sensors in a discreet but effective way. It can look down on you from an upper corner in your kitchen or stand on your sideboard to watch over your living room. You can also keep it simple and tape the Motion Sensor Pro to a wall in your rooms.
Your user-friently housesitter. Don’t waste your time on complex instruction manuals. There’s no need for the hassle when you have a frient to take care of it. The Motion Sensor Pro offers advanced technology but is easy to install. With great usability comes great responsibility, and your frient won’t disappoint you. It makes safety and automated home routines uncomplicated. Wake up, go to work, feel in control. Eat, sleep, relax, repeat. Home is always a click away.
Unlike the FRIZMOSZB-141, the frient Motion Sensor Pro (Zigbee) provides you a temperature and light sensor as well as tamper protection.
Specifications:
Please note that a Zigbee gateway is required for notification on your smartphone.
Download high resolution images for frient products.
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Here are a few hints for network installation if things dont work as expected.
Dimensions | 0.0680000x0.0510000x0.0680000 mm |
Weight | 110 gr |
Frequency | XXfrequency |
Maximum transmission power | XXantenna |