MerryIoT Helium (Browan)
MerryIoT Helium HNT Hotspot Miner V1 LoRaWAN
SKU: BROWL0001
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
Become a part of the Helium People’s Network and mine cryptocurrency.
Helium is a decentralized global LoRaWAN network, which is built by the people. The global network is empowered by a new cryptocurrency – HNT and enables everybody to mine it. You can become a part of the Helium network today, because no expensive and wasteful GPU is needed to mine the HNT cryptocurrency. Instead the mining is done via the radio technology of a LoRaWAN Helium Hotspot.
We as Z-Wave Europe are glad to offer you the MerryIoT Helium HNT Hotspot Miner V1.
The steps to start mining are childishly simple:
- Get the MerryIoT Helium HNT Hotspot Miner V1.
- Setup the Hotspot Miner in your home or office by using the Helium app.
- Wait until the Hotspot is verified.
DONE! Now you Earn cryptocurrency by being part of the LoRaWAN Helium network.
Find out more about Helium:
- More information about Helium: https://www.helium.com/
- Find out more about the Helium network coverage in your area: https://explorer.helium.com/
- Helium documentations: https://docs.helium.com/
MerryIoT Helium HNT Hotspot Miner V1 is designed for edge computing applications in IoT, Smart Manufacturing, Automation, Blockchain, etc., to support high performance, reliability, and high throughput for the heavy data processing demand.
MerryIoT Hotspot Miner V1 is targeting AIoT applications with quad A55 cores, G52 GPU hardware, based on Linux distribution. IoT solution providers can easily integrate advanced and stable functions for their application-centric development on their own IoT projects.
Features:
- Number of Channels: Up to 8 concurrent channels for LoRa transmission
- Built-in 2.4G 802.11b/g/n Wireless LAN
- WAN Protocol: LoRaWAN
- Modulation: Based on LoRaWAN
- RF Transceiver: SX1302 with SX1250 / SX1308 with SX1257
- Transmit RF Power: 0.4W (up to 26 dBm)
- Receive Sensitivity: Down to -141 dBm@SF12, BW125KHz
- Bluetooth: Bluetooth 5.2
- Operating Temperature: -10ºC ~ 40ºC
- Storage Temperature: -20ºC ~ 70ºC
- Power Supply: 12V/1~1.5A via DC jack
- Antenna Type: 1 Built-in Wi-Fi antenna, and 1 external LoRa antenna
- Various Internet connections: Ethernet, Wi-Fi (Wireless bridge)
- Frequency Band: EU868 (862~870 MHz)
- Interfaces: 1 LAN (1Gbps) via RJ45, 1 DC jack for power input, 4 LED indicators + 1 Logo LED indicators, 1 Push Button, 1 External TF card slot, 1 External USB-A 2.0 connector, 1 External LoRa antenna
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| Dimensions | 0.1100000x0.0200000x0.1400000 mm |
| Weight | 450 gr |
| EAN | 0079163256432 |
| Frequency | Europe - 868,4 Mhz |
| Maximum transmission power | 5 mW |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.