Aqara
Aqara Smart Plug Type F (Zigbee)
SKU: AQAZSP-EUC01
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
Plug it. Automate it. Control it. Understand how much elctricity you are spending.
Intelligence is in control.
Appliances turn on when needed and off when not. On a schedule. Or intelligently automated and triggered when needed. You are completely in control. It is smart because it can be automated. But it"s also a smart plug because the power to turn it on or off manually is always yours.
In real time and with 99% accuracy.
The Aqara Smart Plug Zigbee will analyse appliances electricity consumption helping you save what you spend.
Automate Your Appliances.
The Aqara Smart Plug Zigbee can automate appliances easily. Numerous smart scenes are available when the plug works with other Aqara smart devices.
Remote Control with Your Smartphone.
Forgot to turn off the fan when you hurry outside? Just take out your phone and open Aqara Home app. Then, you can turn off all the electrical appliances at your home easily.
With Timer Mode, You Can Lead a Carefree Life
Enjoy Smart Life.
Aqara Smart Plug work with your favorite smart home platforms like Aqara Home, Apple HomeKit, Amazon Alex, Google Assistant, and can be conveniently integrated with different smarthome devices.
*Controlling this HomeKit-enabled accessory automatically and away from home requires an Apple TV with tvOS 10.2 or later or an iPad with iOS 11.0 or later or a Home Pod set up as a home hub.
Voice Control.
Use your favourite voice assistant to enjoy a smart life.
It is recommended to use iOS 12.0 or above. A HomePod, Apple TV ( tvOS 11.0 or above ) or an iPad ( iOS 12.0 or above ) that has been set as the home center is needed to remote control HomeKit accessories.
Smart Connection Is Stable and Convenient.
The advantages of the Zigbee protocol make smart devices respond fast and work smoothly. Even if the network connection is interrupted, the local automation between the smart plug and the sensors still works normally.
Power Consumption Report.
The Aqara Smart Plug can record the power consumption of appliances on a daily or monthly basis, helping you monitor the power consumption and save money on your monthly energy bills.
The Aqara Smart Plug does not support appliances over 16A.
Overheat and Overload Protection.
When the load power or the temperature of the plug is above the set standard, it will automatically cut off the power to avoid any danger.
Multiple Safeguards to Ensure Your Safety.
Utilizing V-0 grade flame-retardant material, the Aqara Smart Plug is safe and reliable. It is equipped with a protective shell to prevent electric shock by accident. It can support home appliances with a maximum power consumption of 2300W.
Features:
- Smart Plug Zigbee
- Model: SP - EUC01
- Wireless Standard: Zigbee 3.0
- Electrical Rating: 250V AC,50/60 Hz, 10A,MAX.2300W
- Ambient Temperature: 0°C~35°C (32?~95?)
- Operating Humidity: 0 - 95% RH, non-condensing
- Compatible with Homekit (via Aqara Hub)
- Dimensions: ? 62 × 77.5 mm ( ? 2.44 × 3.05 in.)
- App: Apple Home app (iOS 10.3 or later), Aqara Home app (Android 5.0 or later, iOS 10.3 or later)
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| Dimensions | 0.0620000x0.0620000x0.0770000 mm |
| Weight | 90 gr |
| EAN | 6970504210646 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.