Aqara
Aqara Presence Sensor FP2 Wi-Fi
SKU: AQALPS-S02D
Quickstart
This is a
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.What is Z-Wave?
Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.
Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.
This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.
If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.
For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.
Product Description
Reinvent your space.
The Aqara Presence Sensor FP2 uses state-of-the-art millimeter wave radar technology that can accurately detect the presence of people even with slight movements. This technology ensures the continuity and stability of the smart device. It also has the zone positioning function, which allows it to automate different conditions in different zones, such as beds and tables. A room can now be divided into up to 30 small zones and detect up to five targets (multi-person detection). It can also control other smart home devices through ecosystems such as Apple Home for broader application. It offers features like fall detection and a built-in light sensor. Likewise, it is a great a great helper that can really combine the diversity of the user"s home life and automate different personalities. Selling points: (Selling points are ordered by their priorities).
Zone positioning.
It offers significant advantages over conventional PIR infrared motion sensors, a single radar sensor is required to monitor rooms up to about 40 m². Moreover, you can divide it into up to 30 zones, e.g. sofa, bed or desk. In addition, you can set up individual automation for each zone.
Multi-person detection
Up to 5 target persons can be detected simultaneously. The result is that the sensor not only divides the space, but also automatically responds to the position of different people without interfering with each other.
Ultra-high precision
Privacy and detection accuracy are considered. It is able to detect non-inductive signal detection without collecting real images. Images. Automation can generally be done locally. Millimeter wave radar technology is more stable than detection with infrared sensors, even when sitting or sleeping.
Control other devices via HomeKit, etc.
The FP2 as a multiple sensor in HomeKit (and Home Assistant), Alexa and Google Home. You can easily integrate the sensor without needing a hub, which is obviously the best solution for smart home enthusiasts to expand their smart home setup.
Fall detection and alarms
If someone falls in a room, the FP2 can detect this and notify you. The range is a circle with a radius of 2 meters, and the accuracy of fall detection is >98%. The recommended installation height is 2.5 m - 2.8 m.
Built-in light sensor
Fully functional light detection sensor in Aqara ecosystem. With it, lighting automation becomes much more flexible and convenient. The built-in light sensor also enables advanced home automation.
IPX5 and hidden USB-C® port
Due to its IP rating, the sensor can also be installed in humid environments such as bathrooms. The sensor has an open USB-C® connector that allows you to swap out the included cable for any USB-C compatible cable for placement flexibility.
Features:
- Zone positioning
- Multi-person detection
- Fall detection and alarms
- Built-in light sensor Radar
- Operation Frequency 60 - 64 GHz
- Radio standard: Wi-Fi IEEE 802.11 b/g/n 2.4 GHz, Bluetooth 4.2
- Protection class: IPX5
- Operating temperature: -10 °C - 40°C
- Humidity: 0~95% RH no condensation
- Input power: 5VDC 1A
- Connection: USB C
Prepare for Installation / Reset
Please read the user manual before installing the product.
In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.
Safety Warning for Mains Powered Devices
ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.
Inclusion/Exclusion
On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.
Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.
Quick trouble shooting
Here are a few hints for network installation if things dont work as expected.
- Make sure a device is in factory reset state before including. In doubt exclude before include.
- If inclusion still fails, check if both devices use the same frequency.
- Remove all dead devices from associations. Otherwise you will see severe delays.
- Never use sleeping battery devices without a central controller.
- Dont poll FLIRS devices.
- Make sure to have enough mains powered device to benefit from the meshing
Technical Data
| Dimensions | 0.0640000x0.0640000x0.0430000 mm |
| Weight | 78 gr |
| EAN | 6970504219663 |
| Frequency | XXfrequency |
| Maximum transmission power | XXantenna |
Explanation of Z-Wave specific terms
- Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
- Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
- Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
- Inclusion — is the process of adding new Z-Wave devices into a network.
- Exclusion — is the process of removing Z-Wave devices from the network.
- Association — is a control relationship between a controlling device and a controlled device.
- Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
- Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.