Aeon Labs
Z-Wave Multisensor
SKU: AEO_MULTISENS
Quickstart
This is a
Single click the little button behind the battery cover to include or exclude the device. Clicking the little button behind the battery cover will wake up the device and keep it awake.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The Aeon Labs Multisensor is a USB or battery-powered Z-Wave motion sensor, temperature sensor, humidity sensor and lightness sensor in one package. The sensor will send radio signals up to 6 associated Z-Wave devices within its own Z-Wave network when the sensor detects IR changes in front of its viewing window. The Aeon Labs Multisensor complies with the IP43 standard so it can be used outdoors. By adjusting the sensitivity of the sensor you can avoid the triggering due to small animals like dogs or cats. The Aeon Labs Multi Sensor is delivered with a swivelling Back-Mount Arm for wall mount and a Back-Mount Plate for ceiling mount.
Installation
1. Release the Multisensor from the mounting by rotating it counterclockwise (sign: "Lock"/ "Unlock")
2. Put the 4 AAA batteries in the battery compartment.
3. The sensor can be mounted as follows:
(a) For wall mount use the screws with the swivelling Back-Mount Arm. Further fix the sensor with Back-Mount Plate like shown in the picture.
Important: The Multisensor should be mounted with the Temperature/Humidity Sensor facing downwards and positioned on the bottom of the unit to protect it from snow and rain.
(b) For ceiling mount use the screws with the Back-Mount Plate.
4. Mount the Multisensor on the Mount Plate by rotating it clockwise to the "Lock" sign.
The next pictures are showing the effective motion sensor range for ceiling and wall mounting.
Product Usage
The Multisensor reports the temperature, humidity and lightness by request to a Z-Wave gateway or controller. The sensor will send radio signals up to 6 associated Z-Wave devices within its own Z-Wave network.
The sensitivity of the motion detector can be manually adjusted via the Sensitivity Knob at the battery cover. To increase the sensitivity rotate the Knob clockwise, to decrease it rotate it counterclockwise.
| Reset to factory default | XXXResetDescription |
| Inclusion | Make sure that your Z-Wave Controller is in the Inclusion-/Exclusion-Mode. Click the little button behind the battery to confirm the process. A successful Inclusion/Exclusion lights up the sensor LED for a few seconds. |
| Exclusion | Make sure that your Z-Wave Controller is in the Inclusion-/Exclusion-Mode. Click the little button behind the battery to confirm the process. A successful Inclusion/Exclusion lights up the sensor LED for a few seconds. |
| NIF | A single click on the little button behind the battery sends a Node Information Frame. |
| Wakeup | A single click on the little button behind the battery will wake up the device and keep it awake. |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Devices to be switched on upon motion deteced and off after a timeout (on time) |
Configuration Parameters
Parameter 1: Sensor report type on Get without instances
Which type of multi sensor report should be sent on multi sensor Get command without instances Size: 1 Byte, Default Value: 00
| Setting | Description |
|---|---|
| 00 | Temperature, humidity and luminance |
| 01 | Temperature |
| 02 | Luminance |
| 03 | Humidity |
Parameter 2: Wake up 10 minutes when batteries are inserted
Stay awake for 10 minutes after batteries are inserted Size: 1 Byte, Default Value: 00
| Setting | Description |
|---|---|
| 00 | No |
| 01 | Yes |
Parameter 3: On time
How long should the device associated to multi senor keep state On before sending it Off command (if the value is bigger than 255, the value would be rounded to next integer in minutes) Size: 2 Byte, Default Value: 00f0
| Setting | Description |
|---|
Parameter 4: Enable motion sensor
Size: 1 Byte, Default Value: 01
| Setting | Description |
|---|---|
| 00 | Disabled |
| 01 | Enabled |
Parameter 101: Send unsolicited reports periodicaly. Interval group 1
Which reports need to send automatically in timing intervals for group 1 Size: 4 Byte, Default Value: 00000000
| Setting | Description |
|---|---|
| Byte 1: 00000001 | Battery report |
| Byte 1: 00100000 | Temperature |
| Byte 1: 01000000 | Luminosity |
| Byte 1: 10000000 | Humidity |
Parameter 102: Send unsolicited reports periodicaly. Intervcal group 2
Which reports need to send automatically in timing intervals for group 2 Size: 4 Byte, Default Value: 00000000
| Setting | Description |
|---|---|
| Byte 1: 00000001 | Battery report |
| Byte 1: 00100000 | Temperature |
| Byte 1: 01000000 | Luminosity |
| Byte 1: 10000000 | Humidity |
Parameter 103: Send unsolicited reports periodicaly. Intervcal group 3
Which reports need to send automatically in timing intervals for group 3 Size: 4 Byte, Default Value: 00000000
| Setting | Description |
|---|---|
| Byte 1: 00000001 | Battery report |
| Byte 1: 00100000 | Temperature |
| Byte 1: 01000000 | Luminosity |
| Byte 1: 10000000 | Humidity |
Parameter 111: Unsolicitate reports interval for timing groups 1
Interval to send out reports to timing group 1 Size: 4 Byte, Default Value: 000002d0
| Setting | Description |
|---|
Parameter 112: Unsolicitate reports interval for timing groups 2
Interval to send out reports to timing group 2 Size: 4 Byte, Default Value: 000002d0
| Setting | Description |
|---|
Parameter 113: Unsolicitate reports interval for timing groups 3
Interval to send out reports to timing group 3 Size: 4 Byte, Default Value: 000002d0
| Setting | Description |
|---|
Technical Data
| Dimensions | 0.0760000x0.0760000x0.0660000 mm |
| Weight | 79 gr |
| EAN | 1220000010291 |
| Device Type | Routing Multilevel Sensor |
| Generic Device Class | Multilevel Sensor |
| Specific Device Class | Routing Multilevel Sensor |
| Firmware Version | 01.12 |
| Z-Wave Version | 03.1c |
| Certification ID | ZC08-13030002 |
| Z-Wave Product Id | 0086.0002.0005 |
| Frequency | Europe - 868,4 Mhz |
| Maximum transmission power | 5 mW |