Aeon Labs
Z-Wave Clamp Power Meter 1st Edition - three clamps
SKU: AEO_HEM3-G1
Quickstart
This is a
Single click the little button behind the battery cover one time to include or exclude the device. The device is FLIRS.
Important safety information
Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.Product Description
The Aeon Labs Smart Energy Monitor is a low-cost energy monitor for the entire home. It can wirelessly report immediate wattage and kWh usage to central control point gateways and can be easily and safely installed by anyone. Ease and safety are paramount: Electricians are not required to install the Aeon Labs Smart Energy Monitor; the customer never needs to handle hot exposed wiring. Current transformer clamps clamp around the AC Mains to detect energy usage for the entire house. The main body is anchored using a back mount which can be opend easily for battery replacement (every year). Optionally it is possible to power the unit from an external mini USB power supply. The device reports W and kWH.
Installation
The HEM can be placed on every dry place closed to the electric installation to be monitored. The current transformers need to be clamped around single wires. Attention: It is not possible to measure the current in cables that consist of more than one wire. Such a wire must be stripped and the CT is installed on the hot wire only. If there are less wires than the number of CTs this will not harm the operation of the device.
The device can be powered by batteries or by an external power supply that is connected to the HEM via mini USB connector. In case an external power supply is installed, remove the batteries inside!
Product Usage
The device is able to report wattage and electric power consumed on request or ? if configured correctly ? regularly with out being polled. The reporting interval is limited to min 4 minutes if the device is battery operated. The device reports aggregated values and individual values of the clamp. Attention: The wattage value is very dynamic and is measured right at the moment of polling. If both the aggregated value and the values of the individual clamps are polled the result may differ because the values were just taken at different times. In order to operate correctly, a number of configuration settings need to be made.
Configuration parameter #1 defines the local voltage. Attention: It is not possible to set the precise voltage of your mains network, but 110 verus 240 V only. The current transformer clamps will always measure current only and use the set voltage value to calculate the wattage and electric power. If your local main voltage is e.g. 230 V only, you will receive wrong wattage results simply by the fact that the wrong voltage is used for calculation.
| Reset to factory default | XXXResetDescription |
| Inclusion | Single click the little button behind the battery one time to include or exclude the device. |
| Exclusion | Single click the little button behind the battery one time to include or exclude the device. |
| NIF | A single click on the little button behind the battery sends a Node Information Frame. |
| Wakeup | XXXWakeupDescription |
| Protection | XXXProtection |
| FirmwareUpdate | XXXFirmwareUpdate |
| SetAssociation | XXXSetAssociation |
Association Groups:
| Group Number | Maximum Nodes | Description |
|---|---|---|
| 1 | 5 | Receiver of all Reports |
Configuration Parameters
Parameter 2: If the reverse clamping pliers, negative power is detected.
Size: 1 Byte, Default Value: 00
| Setting | Description |
|---|---|
| 00 | Disabled |
| 01 | Enabled |
Parameter 3: Automated Report only when power is changed
Size: 1 Byte, Default Value: 00
| Setting | Description |
|---|---|
| 00 | Disabled |
| 01 | Enabled |
Parameter 4: Minimum Change to send Report (Watt) for the whole HEM
The value represents the minimum change in Wattage for a Report to be sent . Size: 2 Byte, Default Value: 0032
| Setting | Description |
|---|---|
| 00 - 6000 | Value in W |
Parameter 5: Minimum Change to send Report (Watt) for clamp 1
The value represents the minimum change in Wattage for a Report to be sent . Size: 2 Byte, Default Value: 0032
| Setting | Description |
|---|---|
| 00 - 6000 | Value in W |
Parameter 6: Minimum Change to send Report (Watt) for clamp 2
The value represents the minimum change in Wattage for a Report to be sent . Size: 2 Byte, Default Value: 0032
| Setting | Description |
|---|---|
| 00 - 6000 | Value in W |
Parameter 7: Minimum Change to send Report (Watt) for clamp 3
The value represents the minimum change in Wattage for a Report to be sent . Size: 2 Byte, Default Value: 0032
| Setting | Description |
|---|---|
| 00 - 6000 | Value in W |
Parameter 8: Minimum Change to send Report (%) for the whole HEM
The value represents the minimum change in Watage Percent for a report to be sent Size: 1 Byte, Default Value: 0a
| Setting | Description |
|---|---|
| 00 - 100 | Value in % |
Parameter 9: Minimum Change to send Report (%) for clamp 1
The value represents the minimum change in Watage Percent for a report to be sent Size: 1 Byte, Default Value: 0a
| Setting | Description |
|---|---|
| 00 - 100 | Value in % |
Parameter 10: Minimum Change to send Report (%) for clamp 2
The value represents the minimum change in Watage Percent for a report to be sent Size: 1 Byte, Default Value: 0a
| Setting | Description |
|---|---|
| 00 - 100 | Value in % |
Parameter 11: Minimum Change to send Report (%) for clamp 3
The value represents the minimum change in Watage Percent for a report to be sent Size: 1 Byte, Default Value: 0a
| Setting | Description |
|---|---|
| 00 - 100 | Value in % |
Parameter 13: Enable /disable reporting CRC-16 Encapsulation Command
Size: 1 Byte, Default Value: 00
| Setting | Description |
|---|---|
| 00 | Disabled |
| 01 | Enabled |
Parameter 101: Report type send in Reporting Group 1
Defines the type of report sent for the Reporting Group 1. Size: 4 Byte, Default Value: 00000008
| Setting | Description |
|---|---|
| Byte 1: 00000010 | Battery Report |
| Byte 1: 00000100 | MultiSensor Report for the whole device |
| Byte 1: 00001000 | Meter Report for Watt for the whole device |
| Byte 1: 00010000 | Meter Report for kWh for the whole device |
| Byte 2: 00000010 | Meter Report for Watt for clamp 1 |
| Byte 2: 00000100 | Meter Report for Watt for clamp 2 |
| Byte 2: 00001000 | Meter Report for Watt for clamp 3 |
| Byte 2: 00010000 | Meter Report for kWh for clamp 1 |
| Byte 2: 00100000 | Meter Report for Watt for clamp 2 |
| Byte 2: 01000000 | Meter Report for kWh for clamp 3 |
Parameter 102: Report Type send in Reporting Group 2
Defines the type of report sent for the Reporting Group 2. Size: 4 Byte, Default Value: 00000000
| Setting | Description |
|---|---|
| Byte 1: 00000010 | Battery Report |
| Byte 1: 00000100 | MultiSensor Report for the whole device |
| Byte 1: 00001000 | Meter Report for Watt for the whole device |
| Byte 1: 00010000 | Meter Report for kWh for the whole device |
| Byte 2: 00000010 | Meter Report for Watt for clamp 1 |
| Byte 2: 00000100 | Meter Report for Watt for clamp 2 |
| Byte 2: 00001000 | Meter Report for Watt for clamp 3 |
| Byte 2: 00010000 | Meter Report for kWh for clamp 1 |
| Byte 2: 00100000 | Meter Report for Watt for clamp 2 |
| Byte 2: 01000000 | Meter Report for kWh for clamp 3 |
Parameter 103: Report Type send in Reporting Group 3
Defines the type of report sent for the Reporting Group 3. Size: 4 Byte, Default Value: 00000000
| Setting | Description |
|---|---|
| Byte 1: 00000010 | Battery Report |
| Byte 1: 00000100 | MultiSensor Report for the whole device |
| Byte 1: 00001000 | Meter Report for Watt for the whole device |
| Byte 1: 00010000 | Meter Report for kWh for the whole device |
| Byte 2: 00000010 | Meter Report for Watt for clamp 1 |
| Byte 2: 00000100 | Meter Report for Watt for clamp 2 |
| Byte 2: 00001000 | Meter Report for Watt for clamp 3 |
| Byte 2: 00010000 | Meter Report for kWh for clamp 1 |
| Byte 2: 00100000 | Meter Report for Watt for clamp 2 |
| Byte 2: 01000000 | Meter Report for kWh for clamp 3 |
Parameter 111: Send Interval for Reporting Group 1
Defines the time interval when the defined report of Reporting Group 1 is sent out. Size: 1 Byte, Default Value: 01
| Setting | Description |
|---|---|
| 00 - 127 | Value in s |
Parameter 112: Send Interval for Reporting Group 2
Defines the time interval when the defined report of Reporting Group 2 is sent out. Size: 1 Byte, Default Value: 01
| Setting | Description |
|---|---|
| 00 - 127 | Value in s |
Parameter 113: Send Interval for Reporting Group 3
Defines the time interval when the defined report of Reporting Group 3 is sent out. Size: 1 Byte, Default Value: 01
| Setting | Description |
|---|---|
| 00 - 127 | Value in s |
Parameter 100: Set 101-103 to default
Size: 1 Byte, Default Value: 01
| Setting | Description |
|---|
Parameter 110: Set 111-113 to default
Size: 1 Byte, Default Value: 01
| Setting | Description |
|---|
Parameter 200: Partner ID
(0= Aeon Labs Standard Product, 1= AT&T). Size: 1 Byte, Default Value: 01
| Setting | Description |
|---|
Parameter 252: Enable/disable Configuration Locked
0 =disable, 1 = enable Size: 1 Byte, Default Value: 00
| Setting | Description |
|---|---|
| 00 | 0 = disabled |
| 01 | 1 = enabled |
Parameter 254: Device Tag
Size: 2 Byte, Default Value: 0000
| Setting | Description |
|---|
Parameter 255: Reset
Reset configuration set up to default setting Size: 1 Byte, Default Value: 00
| Setting | Description |
|---|
Technical Data
| Device Type | Routing Multilevel Sensor |
| Generic Device Class | Multilevel Sensor |
| Specific Device Class | Routing Multilevel Sensor |
| Firmware Version | 03.38 |
| Z-Wave Version | 02.61 |
| Z-Wave Product Id | 0086.0002.0009 |
| Frequency | Europe - 868,4 Mhz |
| Maximum transmission power | 5 mW |