Quickstart

This is a secure Wall Controller for XXXQFrequencyName. To run this device please insert fresh 1 * LIR2450 batteries. To run this device please make sure the internal battery is fully charged. 1. Insert the LIR2450 battery.
2. Set the Z-Wave network main controller into learning mode (see Z-Wave network controller operating manual).
3. Pressing and holding a button for 3 seconds.
4. If the inclusion is successful, the LED will blink in green less than for 5 seconds and then keep on for 15 seconds.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

Product Description

The NanoMote Quad is a wireless, portable and rechargeable scene switch. It can control a Z-Wave device, such as smart plug, smart dimmer with a Z-Wave gateway. You can also activate a scene like sleep scene, movie scene and entertainment scene with it.

Installation

Open the cover













Insert your battery and close the cover

















Product Usage

LOW BATTERY ALARM FUNCTION

NanoMote Quad will send battery report to the lifeline group when button is triggered during the sleep mode. If the battery level of the NanoMote Quad is less than 20%, the NanoMote Quad will send a low battery alarm to the main controller.

CHILD LOCK FUNCTION

Child Lock function. If enable the Child Lock function, the LED indicator will not be on when press down the button. To switch on/off the Child Lock function, please press and hold the button for 10 seconds, the LED indicator will be solid on in red. Then release the button, the LED indicator will be continuously stay in red for 2 seconds. During this 2 seconds, please click the button once, the LED light will be blink fast in red for 2 seconds.

TESTING Z-WAVE NETWORK RANGE

Press and hold the button for 15 seconds, the LED light will be solid on in purple. Then release the button, the LED light will be stay in purple for 2 seconds, during this 2 seconds, please click the  button once, it will start to test the Z-Wave network range and LED light will blink fast in purple. After finish the test, if the LED light is in green, it refers to strong signal; if in blue, it refers to medium signal, and if in red, it refers to weak signal or no signal.
Tip: This function works only when NanoMote Quad has been included into a ZWave network.

BATTERY CHARGING

NanoMote Quad has an internal rechargeable battery that will run for three months under the normal use condition. The charger‘s output should be a micro USB terminal with the specification of output DC 5V.The LED color is red during the charging process, and it will turn to green if the charging is finished.


Reset to factory default Pressing and holding a button for 20 seconds. Release the button after 20 seconds, LED will keep in yellow for 3 seconds. Scene Controller will be reset to factory defaults if you short press the button within this 3 seconds.Please use this procedure only when the network primary controller is missing or otherwise inoperable.
Inclusion 1. Open the NanoMote
2. Insert the battery
3. Press the button on the NanoMote One twice
Exclusion 1. Press the button on the NanoMote One twice
NIF XXXNIF
Wakeup Pressing and holding a button for 3 seconds. Led will turn to green,which means Scene Controller has been woken up.
Protection XXXProtection
FirmwareUpdate With reference to Wake-up operation (VI.WAKE UP) and Z-Wave controller‘s guidances to do OTA.
SetAssociation XXXSetAssociation

Association Groups:

Group Number Maximum Nodes Description
1 5 NanoMote Quad will send the central scene notification command and battery report command to the associated nodes if any button is triggered.
2 5 NanoMote Quad will send Basic Set command to the associated nodes if button 1 is pressed.
3 5 NanoMote Quad will send switch multilevel set, the multilevel start level change and multilevel stop level change command to the associated nodes if button 1 is pressed, hold and released, respectively.
4 5 NanoMote Quad will send Basic Set command to the associated nodes if button 2 is pressed.
5 5 NanoMote Quad will sendswitch multilevel set, the multilevel start level change and multilevel stop level change command to the associated nodes if button 2 is pressed, hold and released, respectively.
6 5 NanoMote Quad will send Basic Set command to the associated nodes if button 3 is pressed.
7 5 NanoMote Quad will sendswitch multilevel set, the multilevel start level change and multilevel stop level change command to the associated nodes if button 3 is pressed, hold and released, respectively.
8 5 NanoMote Quad will send Basic Set command to the associated nodes if button 4 is pressed.
9 5 NanoMote Quad will sendswitch multilevel set, the multilevel start level change and multilevel stop level change command to the associated nodes if button 4 is pressed, hold and released, respectively.

Configuration Parameters

Parameter 32: Level of low battery

Define a battery level as the low battery.
Size: 1 Byte, Default Value: 20

Setting Description
10 - 50 when the value is 10% to 50%,it will send a low battery command.

Parameter 41: Enable send central scene notification.

Set of sending central scene notification or not.
Size: 1 Byte, Default Value: 1

Setting Description
0 Disable
1 Enable

Parameter 42: Setting the duration value of the command switch multilevel.

Setting the duration value of the command switch multilevel.
Size: 1 Byte, Default Value: 255

Setting Description
0 - 255 The higher the value,the long the duration value of the command switch multilevel

Parameter 43: Enable/disable the buzzer alarm when battery is running low.

Set the buzzer alarm or not when battery is low.
Size: 1 Byte, Default Value: 0

Setting Description
0 Disable
1 Enable

Technical Data

Dimensions 50 x 50 x 14 mm
Weight 26 gr
Hardware Platform ZM5101
EAN 1220000016118
IP Class IP 20
Voltage 3,6 V
Battery Type 1 * LIR2450
Device Type Wall Controller
Network Operation Portable Slave
Z-Wave Version 6.71.01
Certification ID ZC10-18036056
Z-Wave Product Id 0x0371.0x0002.0x0003
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW
EuropeWall Controller