This is a
1. Ensure the led bulb has been excluded outside the network.
2. Triggered by OFF ->ON (between 0.5-2 seconds each time)3.LED solid yellow Color (0xFFFF00) during the pairing(Timeout is 10 seconds).
Failure: Blinks between 100% White and Red 0x0000FF color for 3 seconds (at a rate of 200ms per flash), Once 3 seconds have passed, the LED should return to a Warm White LED at 100%
Success: Blinks between 100% White and Green 0x00FF00 color for 3 seconds (at a rate of 200ms per flash). Once 3 seconds have passed, the LED should return to a Warm White LED at 100%.
Reset to factory default | 1. Assuming led bulb was added to controller and was power on. 2. RGBW bulb re-power 6 times (between 0.5-2 seconds each time).Note: ON -> OFF -> ON -> OFF -> ON -> OFF -> ON -> OFF -> ON -> OFF -> ON -> OFF -> ON 3. If the 6th power on, the led bulb change to Yellow color(into pairing process ), which means that the reset factory settings are successf. |
Inclusion | 1. Install the device according to the instructions. 2. Switch ON the bulb. 3. LED Bulbs LED will blink 2x times to indicate that it is looking for a Z-Wave network to connect to. |
Exclusion | 1. Turn on the Bulb. 2. Switch the Bulb off and on 3 times in a row (between 0.5 - 2 seconds per re-power). |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 1 | Lifeline - Set configuration parameter 80. |
User custom mode for LED animations. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable custom mode |
1 | Blink Colors in order mode. |
2 | Randomized blink color mode |
Enable/Disable Strobe over Custom Color. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable Strobe over Custom Color. |
1 | Enable Strobe over Custom Color. |
Set the rate of change to next color in Custom Mode. Size: 1 Byte, Default Value: 50
Setting | Description |
---|---|
5 - 8640000 | Set the specified rate of change to next color in Custom Mode. |
Set color that LED Bulb blinks in (Blink Mode). If you set a value of 6 (2+4), LED Bulb blink between (Red -> Orange) in a cycle. If you set a value 255, LED Bulb will blink all colors in a cycle. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
1 | White |
2 | Red |
4 | Orange |
8 | Yellow |
16 | Green |
32 | Blue |
64 | Indigo |
128 | Purble |
Ramp rate when dimming using Multilevel Switch V1 CC in 100ms Size: 1 Byte, Default Value: 20
Setting | Description |
---|---|
0 - 100 | Specifying the ramp rate when dimming using Multilevel Switch V1 CC in 100ms |
Enable to send notifications to associated devices(Group 1) when the state of LED Bulb is changed. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Nothing |
1 | Send basic report to associated devices when the state of the LED Bulb is changed |
The user can configure the parameter to adjust the color component Warm White. Size: 2 Byte, Default Value: 2700
Setting | Description |
---|---|
2700 - 4999 | Value range =Warm White in Kelvin (K) |
The user can configure the parameter to adjust the color component Cold White. Size: 2 Byte, Default Value: 6500
Setting | Description |
---|---|
5000 - 6500 | Value rang = Cold White in Kelvin (K) |
Dimensions | 0.0600000x0.1200000x0.0600000 mm |
Weight | 132.87 gr |
Hardware Platform | ZM5101 |
EAN | 1220000016095 |
IP Class | IP 20 |
Voltage | 230 V |
Device Type | Light Dimmer Switch |
Network Operation | Always On Slave |
Z-Wave Version | 6.51.09 |
Certification ID | ZC10-18046097 |
Z-Wave Product Id | 0x0371.0x0003.0x0002 |
Color | White |
Firmware Updatable | Updatable by Consumer by RF |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |