This is a
1. Install the device according to the instructions.
2. Press the button two times quickly on the Nano Switch.
Aeotec Nano Switch is a low-cost Z-Wave Switch specifically used to enable Z-Wave command and control (on/off) of any wall switches. In the event of power failure, non-volatile memory retains all programmed information relating to the unit?s operating status.
It can connect to 2 external manual switches to control the load ON/OFF independently. Its surface has a pin socket, which can be used for connecting to the touch panel, so you can also use the touch panel to control the Nano Switch.
The Dual Nano Switch is also a security Z-Wave device and supports Over The Air (OTA) feature for the products firmware upgrade.
Notes for the wire connection ports:
Reset to factory default | Set Parameter 255 |
Inclusion | 1. Install the device according to the instructions. 2. Press the button two times quickly on the Nano Switch. |
Exclusion | 1. Press the button once on the Dual Nano Switch. |
NIF | XXXNIF |
Wakeup | XXXWakeupDescription |
Protection | XXXProtection |
FirmwareUpdate | XXXFirmwareUpdate |
SetAssociation | XXXSetAssociation |
Group Number | Maximum Nodes | Description |
---|---|---|
1 | 5 | Z-Wave Plus Lifeline.When the load state of Nano Switch (on/off) is changed, the Hail CC, Switch Multilevel Report and Basic Report (configured by parameter 80) can be sent to the associated nodes in this group. |
2 | 5 | Forward the Basic Set, Switch All, Scene Activation Set to associated nodes in Group 2 when the Nano Switch receives the Basic Set, Switch All, Scene Activation Set commands from main controller. |
3 | 5 | Send Basic Set (configured by parameter 82) to the associated nodes in Group 3 when the external switch S1 is operated |
4 | 5 | Send Basic Set (configured by parameter 82) to the associated nodes in Group 4 when the external switch S2 is operated |
Output Load will be turned off automatically after 30 seconds and if the temperature of product inside exceeds 100°C. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Disable |
1 | Enable |
Configure the output status after re-power on it. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Last status |
1 | Always on |
2 | Always off |
To set which notification would be sent to the associated devices (Group 1) when the state of Nano Dimmers load is changed. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Send Nothing |
1 | Send Hail CC |
2 | Send Basic CC report |
3 | Send Hail CC when using the manual switch to change the load state. |
To set which notification would be sent to the associated nodes in association Group 3 when using the external switch 1 to switch the loads. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Send Nothing |
1 | Send Basic Set CC |
To set which notification would be sent to the associated nodes in association Group 4 when using the external switch 2 to switch the loads. Size: 1 Byte, Default Value: 1
Setting | Description |
---|---|
0 | Send Nothing |
1 | Send Basic Set CC |
Configure the state of LED when it is in 3 modes Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | The LED will follow the status (on/off) of its load (Energy mode). |
256 - 316 | The hour value of ON time |
2 | Night light mode. |
Set the ON/OFF time of the LED when it is in Night light mode. Size: 4 Byte, Default Value: 524306
Setting | Description |
---|---|
0 - 60 | The minute time of OFF |
256 - 316 | The hour time of OFF |
65536 - 65596 | The minute time of ON |
16777216 - 16777276 | The hour time of ON |
Set appointment 1 Size: 4 Byte, Default Value: 2293760
Setting | Description |
---|---|
0 - 60 | The minute value of ON time |
256 - 316 | The minute value of ON time |
65536 - 65543 | The day value (Mon to Sun) |
16777215 | Disable the setting. |
16777216 | Enable the setting. |
Set appointment 2 Size: 4 Byte, Default Value: 2293760
Setting | Description |
---|---|
0 - 60 | The minute value of ON time |
256 - 316 | The hour value of ON time |
65536 - 65543 | The day value (Mon to Sun) |
16777215 | Disable the setting. |
16777216 | Enable the setting. |
Configure the external switch mode for S1. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Enter automatic identification mode |
1 | Momentary push button mode |
2 | 3 way switch mode |
3 | 2-state switch mode |
Configure the external switch mode for S2. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Enter automatic identification mode |
1 | Momentary push button mode |
2 | 3 way switch mode |
3 | 2-state switch mode |
Set the control destination of the external switch. Size: 1 Byte, Default Value: 3
Setting | Description |
---|---|
1 | control the output loads of itself. |
2 | control the other nodes |
3 | control the output loads of itself and other nodes. |
Lock/unlock configuration parameters. Size: 1 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Unlock |
1 | Lock |
Reset the Nano Dimmer to factory default. Size: 4 Byte, Default Value: 0
Setting | Description |
---|---|
0 | Reset all configuration parameters to factory default setting |
1431655765 | Reset to factory default setting and removed from the z-wave network |
Dimensions | 0.0425000x0.0400000x0.0200000 mm |
Weight | 28.67 gr |
Hardware Platform | ZM5202 |
EAN | 1220000015050 |
IP Class | IP 20 |
Voltage | 24V DC/ 230V AC |
Load | 10 A |
Device Type | Switch |
Generic Device Class | Binary Switch |
Specific Device Class | Binary Power Switch |
Firmware Version | 01.01 |
Z-Wave Version | 04.26 |
Certification ID | ZC10-17035523 |
Z-Wave Product Id | 0x0086.0x0003.0x008b |
Frequency | Europe - 868,4 Mhz |
Maximum transmission power | 5 mW |