Quickstart

This is a secure On/Off Power Switch for Europe. To run this device please connect it to your mains power supply.

A To include the device turn the primary controller of Z-Wave network into inclusion mode, short press the product?s Z-Wave button that you can find on the product"s housing.



Important safety information

Please read this manual carefully. Failure to follow the recommendations in this manual may be dangerous or may violate the law. The manufacturer, importer, distributor and seller shall not be liable for any loss or damage resulting from failure to comply with the instructions in this manual or any other material. Use this equipment only for its intended purpose. Follow the disposal instructions. Do not dispose of electronic equipment or batteries in a fire or near open heat sources.

What is Z-Wave?

Z-Wave is the international wireless protocol for communication in the Smart Home. This device is suited for use in the region mentioned in the Quickstart section.

Z-Wave ensures a reliable communication by reconfirming every message (two-way communication) and every mains powered node can act as a repeater for other nodes (meshed network) in case the receiver is not in direct wireless range of the transmitter.

This device and every other certified Z-Wave device can be used together with any other certified Z-Wave device regardless of brand and origin as long as both are suited for the same frequency range.

If a device supports secure communication it will communicate with other devices secure as long as this device provides the same or a higher level of security. Otherwise it will automatically turn into a lower level of security to maintain backward compatibility.

For more information about Z-Wave technology, devices, white papers etc. please refer to www.z-wave.info.

Product Description

Aeon Labs Garage Door Controller is a smart and wireless Garage Door Control system, you can control the garage door to open, close, or stop moving via wireless signal on your gateway client or phone application.

Prepare for Installation / Reset

Please read the user manual before installing the product.

In order to include (add) a Z-Wave device to a network it must be in factory default state. Please make sure to reset the device into factory default. You can do this by performing an Exclusion operation as described below in the manual. Every Z-Wave controller is able to perform this operation however it is recommended to use the primary controller of the previous network to make sure the very device is excluded properly from this network.

Reset to factory default

This device also allows to be reset without any involvement of a Z-Wave controller. This procedure should only be used when the primary controller is inoperable.

To reset the device press and hold the Z-Wave Button for 20 seconds and then release it. Your Garage Door Controller will now be reset to its original settings, and the Network LED will be solid for 2 seconds and then start slow blinking to confirm a success.

Safety Warning for Mains Powered Devices

ATTENTION: only authorized technicians under consideration of the country-specific installation guidelines/norms may do works with mains power. Prior to the assembly of the product, the voltage network has to be switched off and ensured against re-switching.

Installation

The Garage Door Controller must be installed in your home and near the garage door. It cannot be installed outdoors in elements such as rain and snow.

  1. Utilize the provided 20mm screws to affix it to the desired surface.

  2. Connect the 2 Switch cables to the Switch Connector 1 and 2 on the Garage Door Controller, and then use the Fast Wiring Clip to connect the 2 Switch Cables to the Motor Switch Cables, see the figure below.

  3. Now lock the Garage Door Controller to the Back Mount Plate by twisting the Garage Door Controller.

Installing the Sensor on your garage door.

Affix your sensor mounting plate to the garage door. The sensor mount plate should be installed on the top of the garage door (on the left, middle, or right side). Now affix your sensor mounting plate to the surface. Your mounting plate can be affixed using screws or double-sided tape. If you are using screws, attach the mounting plate to the respective surface using the two 20mm screws provided.

Inclusion/Exclusion

On factory default the device does not belong to any Z-Wave network. The device needs to be added to an existing wireless network to communicate with the devices of this network. This process is called Inclusion.

Devices can also be removed from a network. This process is called Exclusion. Both processes are initiated by the primary controller of the Z-Wave network. This controller is turned into exclusion respective inclusion mode. Inclusion and Exclusion is then performed doing a special manual action right on the device.

Inclusion

  1. Unlock the Back Mount Plate of Garage Door Controller by twisting the Back Mount Plate and separating the two parts of your Garage Door Controller.

  2. Power your Garage Door Controller by connecting the 5V DC Adapter to the input.

  3. Now that your Garage Door Controller is powered on, you will see the Network LED blinking slowly. Bring your gateway into the inclusion mode and press the Z-Wave button of the garage door controller.

Exclusion

  1. Unlock the Back Mount Plate of Garage Door Controller by twisting the Back Mount Plate and separating the two parts of your Garage Door Controller.

  2. Bring your gateway into the exclusion mode and press the Z-Wave button of the garage door controller three times.

Quick trouble shooting

Here are a few hints for network installation if things dont work as expected.

  1. Make sure a device is in factory reset state before including. In doubt exclude before include.
  2. If inclusion still fails, check if both devices use the same frequency.
  3. Remove all dead devices from associations. Otherwise you will see severe delays.
  4. Never use sleeping battery devices without a central controller.
  5. Dont poll FLIRS devices.
  6. Make sure to have enough mains powered device to benefit from the meshing

Association - one device controls an other device

Z-Wave devices control other Z-Wave devices. The relationship between one device controlling another device is called association. In order to control a different device, the controlling device needs to maintain a list of devices that will receive controlling commands. These lists are called association groups and they are always related to certain events (e.g. button pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive the same wireless command wireless command, typically a 'Basic Set' Command.

Association Groups:

Group Number Maximum Nodes Description
1 5 Group 1 is assigned to the Lifeline association group and every device has 5 nodes to associate. When the Garage Door controller is received the commands sent by controller to be turned on or off, the Garage Door controller will send a basic report of its status to the nodes in association group 1. To change what kind of signal is sent to the nodes in group 1, please see the detailed description of configuration parameter 80.
2 5 When the Garage Door Controller receives the Basic Set, Switch Binary Set,commands from main controller. it will forward the Basic Set, Switch Binary Set to associated nodes in Group 2.

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better to user needs or unlock further enhanced features.

IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 ... 255 the value sent in the application shall be the desired value minus 256. For example: To set a parameter to 200 it may be needed to set a value of 200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given as negative values too.

Parameter 32: Startup ringtone

Configure the Startup ringtone
Size: 1 Byte, Default Value: 1

Setting Description
0 Disable
1 - 100 Enable the Startup ringtone.

Parameter 34: Sensor Calibration

1. Let the garage door move to full close position. 2. Send this parameter (0x22) with “value=1” to Garage Door Controller. 3. Let the garage door move to full open position. 4. Let the garage door move to full close position after the step 3 is completed. After the step 4 is completed, all calibration steps are complete.
Size: 1 Byte, Default Value: 0

Setting Description
1 Start calibration

Parameter 35: Timeouts

Set the timeout of all calibration steps for the Sesnor.
Size: 2 Byte, Default Value: 60

Setting Description
1 - 65535 Time in seconds

Parameter 36: Alarm musik

Get the numbers of alarm music.(does not support Set CC
Size: 1 Byte, Default Value: 01

Setting Description

Parameter 37: Alarm mode for door opening

Value1: configure the frequency of blinking for the Alarm LED,there are 10 levels that 1 to10 level, the minimum frequency is level 1 and the max frequency is level 10. Value2: configure the alarm sound (there are 4 types sound saved in EEPROM and user also can update it). Value3: configure the volume of alarm sound (there are 10 levels, the min volume is 1 level and the max volume is 10 levels). Value4=0, disable the alarm prompt. Value4=1, enable the alarm prompt.
Size: 4 Byte, Default Value: 0

Setting Description
1 - 10 Configure the alarm LED interval.
256 - 356 Select an alarm tone. Four alarm tones are stored on the memory card.
65535 - 65545 Adjust the volume of the alarm tone. There are 10 levels.
1677215 Deactivate the alarm mode.
16777216 Activate the alarm mode.

Parameter 38: alarm mode for door closing

Value1: configure the frequency of blinking for the Alarm LED,there are 10 levels that 1 to10 level, the minimum frequency is level 1 and the max frequency is level 10. Value2: configure the alarm sound (there are 4 types sound saved in EEPROM and user also can update it). Value3: configure the volume of alarm sound (there are 10 levels, the min volume is 1 level and the max volume is 10 levels). Value4=0, disable the alarm prompt. Value4=1, enable the alarm prompt.
Size: 4 Byte, Default Value: 6

Setting Description
1 - 10 Configure the alarm LED interval.
256 - 356 Select an alarm tone. Four alarm tones are stored on the memory card.
65535 - 65545 Adjust the volume of the alarm tone. There are 10 levels.
1677215 Deactivate the alarm mode.
16777216 Activate the alarm mode.

Parameter 39: Prompt mode of unknown state:

Value1: configure the frequency of blinking for the Alarm LED,there are 10 levels that 1 to10 level, the minimum frequency is level 1 and the max frequency is level 10. Value2: configure the alarm sound (there are 4 types sound saved in EEPROM and user also can update it). Value3: configure the volume of alarm sound (there are 10 levels, the min volume is 1 level and the max volume is 10 levels). Value4=0, disable the alarm prompt. Value4=1, enable the alarm prompt.
Size: 4 Byte, Default Value: 0

Setting Description
1 - 10 Configure the alarm LED interval.
256 - 356 Select an alarm tone. Four alarm tones are stored on the memory card.
65535 - 65545 Adjust the volume of the alarm tone. There are 10 levels.
1677215 Deactivate the alarm mode.
16777216 Activate the alarm mode.

Parameter 40: Prompt mode of full closing

Value1: configure the frequency of blinking for the Alarm LED,there are 10 levels that 1 to10 level, the minimum frequency is level 1 and the max frequency is level 10. Value2: configure the alarm sound (there are 4 types sound saved in EEPROM and user also can update it). Value3: configure the volume of alarm sound (there are 10 levels, the min volume is 1 level and the max volume is 10 levels). Value4=0, disable the alarm prompt. Value4=1, enable the alarm prompt.
Size: 4 Byte, Default Value: 0

Setting Description
1 - 10 Configure the alarm LED interval.
256 - 356 Select an alarm tone. Four alarm tones are stored on the memory card.
65535 - 65545 Adjust the volume of the alarm tone. There are 10 levels.
1677215 Deactivate the alarm mode.
16777216 Activate the alarm mode.

Parameter 41: Tamper report


Size: 1 Byte, Default Value: 0

Setting Description
0 Sensor is not removed (read only)
16 Sensor 1 is removed (read only)
240 Sensor 2 is removed (read only)
1431655767 Alarm reset (write only)

Parameter 42: Battery report (read only)

Use this configuration report to report the battery power state of Sensor
Size: 1 Byte, Default Value: 0

Setting Description
0 Battery power is much more.
16 Battery power of Sensor 1 is in low battery.
240 battery power of Sensor 2 is in low battery

Parameter 43: Play/stop music

Play/stop music, which can be used to audition/test the music
Size: 1 Byte, Default Value: 0

Setting Description
1 - 254 Play the music that you selected.
255 Stop playing music.

Parameter 44: Volume

Set the volume, which can be used to audition/test volume of music
Size: 1 Byte, Default Value: 0

Setting Description
1 - 10 Volume

Parameter 45: Environment temperature (read only)

The report values that have 4 bytes and its accuracy is 1/1000 after be converted to decimal.
Size: 2 Byte, Default Value: 0

Setting Description

Parameter 46: Blinking frequency of alarm LED.


Size: 1 Byte, Default Value: 0

Setting Description
1 - 10 blinking frequency of alarm LED.

Parameter 47: Button +/-


Size: 1 Byte, Default Value: 0

Setting Description
0 Short pressing the “Button +/-” will be used to adjust 0 1 9 the volume of sound. Long pressing the “Button +/-” will be used to switch the sound to the next.
1 Short pressing the “Button +/-” will be used to switch the sound to the next. Long pressing the “Button +/-” will be used to adjust the volume of sound.

Parameter 80: Hail CC/configuration report

It will send the Hail CC/configuration report CC when the state of garage door is changed
Size: 1 Byte, Default Value: 2

Setting Description
0 not send
1 send Hail CC
2 send configuration report CC
3 Send Hail CC when the garage door state is changed just only by wireless control.

Parameter 200: Partner ID


Size: 1 Byte, Default Value: 0

Setting Description

Parameter 241: Pair the Sensor with Garage Door Controller

Send Configuration Set Value=0x55555501, which will trigger to start the pairing of Sensor (installed on the top of the garage door), at this time, the Network LED on the Garage Door Controller will blink slowly and then short press Temper Switch back of the Sensor. If pairing is successful, the Network LED will stop blinking and the Garage Door Controller will send the configuration report with value=0x01FF to primary controller/gateway. Otherwise, repeat the operation. Note: 1. If you do not press the Temper Switch when starting the pairing mode, the pairing status will keep for 8 second and then exit the pairing status automatically. 2. The Sensor has been paired with the Garage Door Controller after factory.
Size: 4 Byte, Default Value: 0

Setting Description
0 Enable

Parameter 252: Enable/disable configuration locked


Size: 1 Byte, Default Value: 0

Setting Description
0 Aktiviert
1 Disable

Parameter 255: Factory Reset


Size: 4 Byte, Default Value: 1

Setting Description
0 Reset All configurations to default value.
1431655765 Reset to default factory setting and send the Device Reset Locally CC.

Technical Data

Dimensions 0.1160000x0.1160000x0.0330000 mm
Weight 170 gr
EAN 1220000012646
IP Class IP 20
Voltage 5V DC for Garage Door Controller
Load 2W
Battery Type 1 * CR2 3V 800mA for Sensor
Device Type On/Off Power Switch
Generic Device Class Binary Switch
Specific Device Class Binary Power Switch
Firmware Version 01.02
Z-Wave Version 03.63
Certification ID ZC10-15090012
Z-Wave Product Id 0x0086.0x0003.0x003e
Frequency Europe - 868,4 Mhz
Maximum transmission power 5 mW

Supported Command Classes

  • Basic
  • Switch Binary
  • Association Grp Info
  • Zwaveplus Info
  • Configuration
  • Manufacturer Specific
  • Powerlevel
  • Firmware Update Md
  • Association
  • Version
  • Security
  • Device Reset Locally
  • Hail

Controlled Command Classes

  • Device Reset Locally
  • Hail

Explanation of Z-Wave specific terms

  • Controller — is a Z-Wave device with capabilities to manage the network. Controllers are typically Gateways,Remote Controls or battery operated wall controllers.
  • Slave — is a Z-Wave device without capabilities to manage the network. Slaves can be sensors, actuators and even remote controls.
  • Primary Controller — is the central organizer of the network. It must be a controller. There can be only one primary controller in a Z-Wave network.
  • Inclusion — is the process of adding new Z-Wave devices into a network.
  • Exclusion — is the process of removing Z-Wave devices from the network.
  • Association — is a control relationship between a controlling device and a controlled device.
  • Wakeup Notification — is a special wireless message issued by a Z-Wave device to announces that is able to communicate.
  • Node Information Frame — is a special wireless message issued by a Z-Wave device to announce its capabilities and functions.