Dies ist ein
Turn the primary controller of Z-Wave network into inclusion mode, press the external switch of LED Bulb to turn it off and then press the external switch again to turn it on.
Z-Wave ist der internationale Funkstandard zur Kommunikation von Geräten im intelligenten Haus. Dies ist ein Z-Wave Gerät und nutzt die im Quickstart angegebene Funkfrequenz.
Z-Wave ermöglicht eine sichere und stabile Kommunikation indem jede Nachricht vom Empfänger rückbestätigt wird (Zweiwege-Kommunikation) und alle netzbetriebenen Geräte Nachrichten weiterleiten (Routing) können, wenn eine direkte Funkbeziehung zwischen Sender und Empfänger gestört ist.Dank Z-Wave können Produkte unterschiedlicher Hersteller miteinander in einem Funknetz verwendet werden. Damit ist auch dieses Produkt mit beliebigen anderen Produkten anderer Hersteller in einem gemeinsamen Z-Wave Funknetz einsetzbar.
Wenn ein Gerät die spezielle sichere Kommunikation unterstützt dann wird es immer dann mit einem anderen Gerät sicher kommunizieren, wenn dieses Gerät auch eine sichere Kommunikation unterstützt. Ansonsten wird aus Kompatibilitätsgründen auf einen normalen Kommunikation umgeschaltet.
Weitere Informationen wie Produktneugkeiten, Tutorials, Supportforen etc. erhalten Sie auf www.zwave.de.
Aeotec LED Bulb is a low-cost Z-Wave LED module which allows control (on/off/dim) with the use of Z-Wave. Its a bulb has a Smart RGB LED, which can be used to add colour to your home. The bulb has 5 main colour channels available for you to adjust: Red, Green, Blue, Warm White and Cold White. You can configure its colour according to your favour.The LED Bulb is also a security Z-Wave device and supports the Over The Air (OTA) feature for the products firmware upgrade.
Bitte lesen Sie die Benutzeranleitung bevor Sie das Gerät in Betrieb nehmen.
Damit ein Z-Wave zu einem neuen Netz hinzugefügt werden kann muss es sich im Auslieferungs- oder Reset-Zustand befinden. Im Zweifel ist es sinnvoll, eine Exklusion durchzuführen, um das Gerät ganz sicher in diesem Zustand zu bringen. Diese Exklusion kann von jedem beliebigen Z-Wave Controller durchgeführt werden.
Dieses Gerät kann auch ohne Hilfe eines Controller in den Reset-Zustand zurückgeführt werden. Dies sollte jedoch nur dann gemacht werden wenn der Primärcontroller des Z-Wave-Netzes nicht mehr verfügbar oder defekt ist.
Turn the controller of Z-Wave network into exclusion mode, press the external switch of LED Bulb to turn off and then press the external switch again to turn on it, repeat the operation 3 times.After the LED Bulb is excluded from network, it will be reset to factory default state.Use this procedure only in the event that your primary network controller is missing or inoperable.
Achtung: Je nach nationalen Sicherheitsnormen kann es nur autorisierten und/oder ausgebildeten Techniker erlaubt sein, elektrische Installationen am Spannungsnetz vorzunehmen. Bitte informieren Sie sich vor der Installation über die Rechtslage.
Im Auslieferungszustand ist das Gerät mit keinem Z-Wave-Netz verbunden. Damit es
mit anderen Z-Wave Geräten kommunizieren kann, muss es in ein bestehendes Z-Wave Netz
eingebunden werden. Dieser Prozess wird bei Z-Wave Inklusion genannt. Geräte können
Netzwerke auch wieder verlassen. Dieser Prozess heißt bei Z-Wave Exklusion. Beide
Prozesse werden von einem Controller gestartet, der dazu in einen Inklusion- bzw.
Exklusion-Modus geschaltet werden muss. Das Handbuch des Controllers enthält
Informationen, wie er in diese Modi zu schalten ist. Erst wenn der Controller
des Z-Wave Netzes im Inclusion-Modus ist, können Geräte hinzugefügt werden.
Das Verlassen des Netzes durch Exklusion führt zum Rücksetzen dieses Gerätes
in den Auslieferungszustand.3>
Inklusion
Turn the primary controller of Z-Wave network into inclusion mode, press the external switch of LED Bulb to turn it off and then press the external switch again to turn it on.
Exklusion
Turn the primary controller of Z-Wave network into exclusion mode, press the external switch of LED Bulb to turn off and then press the external switch again to turn on it, repeat the operation 3 times.
Die folgenden kleinen Hinweise können bei Problemen im Z-Wave Netz helfen.
Z-Wave Geräte können andere Geräte direkt steuern. Diese direkte Steuerung heißt in Z-Wave Assoziation. In den steuernden Geräten muss dazu die Geräte-ID des zu steuernden Gerätes hinterlegt werden. Dies erfolgt in sogenannten Assoziationsgruppen. Eine Assoziationsgruppe ist immer an ein Ereignis im steuernden Gerät gebunden (Tastendruck oder Auslösen eines Sensors). Bei Eintritt dieses Ereignisses wird an alle in einer Assoziationsgruppe hinterlegten Geräte ein Steuerkommando - meist ein BASIC SET - gesendet.
Gruppen-Nummer | Max. Anzahl Geräte | Beschreibung |
---|---|---|
1 | 5 | The association group 1 is the Z-Wave Lifeline group. The Hail CC and Basic Report CC (configurable) can be sent to the associated nodes in association group 1. |
2 | 5 | In this group, the Basic Set, Switch Binary Set, Switch Multilevel Start Level Change, Switch Multilevel Stop Level Change, Switch Multilevel Set, Scene Activation Set commands would be sent to the associated nodes in association group 2 when the Bulb receives the Basic Set, Switch Binary Set, Switch Multilevel Start Level Change, Switch Multilevel Stop Level Change, Switch Multilevel Set, Scene Activation Set commands from the main controller. |
Z-Wave Produkte können direkt nach der Inklusion im Netz verwendet werden. Durch Konfigurationseinstellungen kann das Verhalten des Gerätes jedoch noch besser an die Anforderungen der Anwendung angepasst und zusätzliche Funktionen aktiviert werden.
WICHTIG: Manche Steuerungen erlauben nur die Konfiguration von vorzeichenbehafteten Werten zwischen -128 und 127. Um erforderliche Werte zwischen 128 und 255 zu programmieren, muss der gewünschte Wert minus 256 eingegeben werden. Beispiel: um einen Parameter auf einen Wert von 200 zu setzen, müsste der Wert 200-256 = -56 eingegeben werden, wenn nur positive Werte bis 128 akzeptiert werden. Bei Werten von 2 Byte Länge wird die gleiche Logik angewandt: Werte über 32768 werden als negative Werte angegeben.
Set the Dimmer mode. Grösse: 1 Byte, Voreingestellt: 0
Wert | Beschreibung |
---|---|
0 | Parabolic curve mode |
1 | Index curve mode |
2 | (Parabolic + Index)/2 mode |
3 | Linear mode |
Set the bulbs state after it is re-powered on. Grösse: 1 Byte, Voreingestellt: 1
Wert | Beschreibung |
---|---|
0 | The last state before re-power on. |
1 | Always On. |
2 | Always Off. |
Enable/disable to lock Configuration parameters. Grösse: 1 Byte, Voreingestellt: 0
Wert | Beschreibung |
---|---|
0 | Disable |
1 | Enable |
Reset the Bulb to factory default. Grösse: 4 Byte, Voreingestellt: 0
Wert | Beschreibung |
---|---|
0 | Reset all configuration parameters to factory default settings |
1431655765 | Reset the bulb to factory default. |
Enable/disable to send out a report when the color is changed. Grösse: 1 Byte, Voreingestellt: 0
Wert | Beschreibung |
---|---|
0 | Disable |
1 | Hail CC |
Get the Bulbs color value.Note: This parameter is a get-only parameter. Grösse: 4 Byte, Voreingestellt: 0
Wert | Beschreibung |
---|---|
1 - 255 | Bule color value |
256 - 65535 | Green color value |
65536 - 16777215 | Red color value |
Enable/disable the function of using External Switch to turn on/off the bulb. Grösse: 1 Byte, Voreingestellt: 0
Wert | Beschreibung |
---|---|
0 | Disable |
1 | Enable |
Enable/disable the function of using External Switch to changes the bulbs color. Grösse: 1 Byte, Voreingestellt: 1
Wert | Beschreibung |
---|---|
0 | Disable |
1 | Enable |
Reboot/save/exit Colorful mode.Note: This parameter is a set-only parameter. Grösse: 1 Byte, Voreingestellt: 0
Wert | Beschreibung |
---|---|
0 | Un-reboot Colorful mode. |
1 | Reboot Colorful mode. |
2 | Exit Colorful mode. |
3 | Save the current Colorful mode value and then to be exited. |
Configure the Colorful mode. Grösse: 4 Byte, Voreingestellt: 157483008
Wert | Beschreibung |
---|---|
0 - 31 | Colour Change Speed Level |
32 - 255 | Time Base of Color Change Speed |
256 - 65535 | Cycle Count |
65536 - 16777215 | Brightness |
16777215 - 134217727 | Color Display Cycle |
134217728 - 1073741823 | Color Change Speed Option |
1073741824 - 2147483647 | Color Transition Style |
Set the Change speed. Grösse: 4 Byte, Voreingestellt: 50332416
Wert | Beschreibung |
---|---|
1 - 255 | Set the pause time of OFF. |
256 - 65535 | Set the pause time of ON. |
65536 - 16777215 | Set the speed from ON to OFF. |
16777216 - 2147483647 | Set the speed from OFF to ON. |
Color index configuration when the bulb is in Multi color mode. Grösse: 4 Byte, Voreingestellt: 2003125025
Wert | Beschreibung |
---|---|
1 - 15 | Index 8 |
16 - 255 | Index 7 |
256 - 4095 | Index 6 |
4096 - 65535 | Index 5 |
65536 - 1048575 | Index 4 |
1048576 - 16777215 | Index 3 |
16777216 - 268435455 | Index 2 |
268435456 - 2147483647 | Index 1 |
To set whcih notification can be sent to the associated devices (Group 1) when the state of LED Bulb is changed. Grösse: 1 Byte, Voreingestellt: 1
Wert | Beschreibung |
---|---|
0 | Nothing |
1 | Hail CC |
2 | Basic CC report. |
Z-Wave Hardware Platform | ZM5101 |
Gerätetyp | Light Dimmer Switch |
Netzwerkfunktion | Always On Slave |
Firmware Version | HW: 98 FW: 1.05 |
Z-Wave Version | 6.51.06 |
Zertifizierungs-ID | ZC10-16065119 |
Z-Wave Produkt Id | 0x0086.0x0103.0x0062 |
Firmware Updatable | Updatable by Consumer by RF |
Z-Wave Scene Type | Scene |
Switch Type | Toggle |
Frequenz | XXfrequency |
Maximale Sendeleistung | XXantenna |