Dies ist ein
1. Place your network controller into Inclusion mode by following the controller manufacturers instructions2. Press any button on the WA00Z-13. A green LED will flash twice to indicate that WA00Z-1 Inclusion is successfulNote: If Inclusion still fails after the 2nd attempt, you need to first manually RESET the ZSC before repeating the above steps.
Z-Wave ist der internationale Funkstandard zur Kommunikation von Geräten im intelligenten Haus. Dies ist ein Z-Wave Gerät und nutzt die im Quickstart angegebene Funkfrequenz.
Z-Wave ermöglicht eine sichere und stabile Kommunikation indem jede Nachricht vom Empfänger rückbestätigt wird (Zweiwege-Kommunikation) und alle netzbetriebenen Geräte Nachrichten weiterleiten (Routing) können, wenn eine direkte Funkbeziehung zwischen Sender und Empfänger gestört ist.Dank Z-Wave können Produkte unterschiedlicher Hersteller miteinander in einem Funknetz verwendet werden. Damit ist auch dieses Produkt mit beliebigen anderen Produkten anderer Hersteller in einem gemeinsamen Z-Wave Funknetz einsetzbar.
Wenn ein Gerät die spezielle sichere Kommunikation unterstützt dann wird es immer dann mit einem anderen Gerät sicher kommunizieren, wenn dieses Gerät auch eine sichere Kommunikation unterstützt. Ansonsten wird aus Kompatibilitätsgründen auf einen normalen Kommunikation umgeschaltet.
Weitere Informationen wie Produktneugkeiten, Tutorials, Supportforen etc. erhalten Sie auf www.zwave.de.
Smart Switch Cover with Z-Wave radio.Built-in Z-Wave radio - can control Z-Wave Light Bulb and switches/dimmers remotely and wirelesslyPlug and play, simple setup. Fits over an existing wall switch.Manually turn on, off, dim your lights while keeping the smart light bulb always online in your home networkWorks with different types and brands of Z-Wave LED Light control devicesPowered by Z-Wave 500 Series module insideManual reset capabilityPowered by 2 pieces of standard CR2032 Lithium Coin Cell with long battery life
Bitte lesen Sie die Benutzeranleitung bevor Sie das Gerät in Betrieb nehmen.
Damit ein Z-Wave zu einem neuen Netz hinzugefügt werden kann muss es sich im Auslieferungs- oder Reset-Zustand befinden. Im Zweifel ist es sinnvoll, eine Exklusion durchzuführen, um das Gerät ganz sicher in diesem Zustand zu bringen. Diese Exklusion kann von jedem beliebigen Z-Wave Controller durchgeführt werden.
Dieses Gerät kann auch ohne Hilfe eines Controller in den Reset-Zustand zurückgeführt werden. Dies sollte jedoch nur dann gemacht werden wenn der Primärcontroller des Z-Wave-Netzes nicht mehr verfügbar oder defekt ist.
In an event that your primary controller is lost or otherwise inoperable, to reset or clear all network information, follow these steps: Factory Reset: Press TOP button 5-times then press BOTTOM button 5-times within 5 seconds
Achtung: Je nach nationalen Sicherheitsnormen kann es nur autorisierten und/oder ausgebildeten Techniker erlaubt sein, elektrische Installationen am Spannungsnetz vorzunehmen. Bitte informieren Sie sich vor der Installation über die Rechtslage.
Im Auslieferungszustand ist das Gerät mit keinem Z-Wave-Netz verbunden. Damit es
mit anderen Z-Wave Geräten kommunizieren kann, muss es in ein bestehendes Z-Wave Netz
eingebunden werden. Dieser Prozess wird bei Z-Wave Inklusion genannt. Geräte können
Netzwerke auch wieder verlassen. Dieser Prozess heißt bei Z-Wave Exklusion. Beide
Prozesse werden von einem Controller gestartet, der dazu in einen Inklusion- bzw.
Exklusion-Modus geschaltet werden muss. Das Handbuch des Controllers enthält
Informationen, wie er in diese Modi zu schalten ist. Erst wenn der Controller
des Z-Wave Netzes im Inclusion-Modus ist, können Geräte hinzugefügt werden.
Das Verlassen des Netzes durch Exklusion führt zum Rücksetzen dieses Gerätes
in den Auslieferungszustand.3>
Inklusion
1. Place your network controller into Inclusion mode by following the controller manufacturers instructions2. Press any button on the WA00Z-13. A green LED will flash twice to indicate that WA00Z-1 Inclusion is successfulNote: If Inclusion still fails after the 2nd attempt, you need to first manually RESET the ZSC before repeating the above steps.
Exklusion
1. Place your network controller into Exclude mode by following the controller manufacturers instructions.2. Press any button on the WA00Z-1 3. The LED will flash twice and WA00Z-1 exclusion is successful.
Die folgenden kleinen Hinweise können bei Problemen im Z-Wave Netz helfen.
Z-Wave Geräte können andere Geräte direkt steuern. Diese direkte Steuerung heißt in Z-Wave Assoziation. In den steuernden Geräten muss dazu die Geräte-ID des zu steuernden Gerätes hinterlegt werden. Dies erfolgt in sogenannten Assoziationsgruppen. Eine Assoziationsgruppe ist immer an ein Ereignis im steuernden Gerät gebunden (Tastendruck oder Auslösen eines Sensors). Bei Eintritt dieses Ereignisses wird an alle in einer Assoziationsgruppe hinterlegten Geräte ein Steuerkommando - meist ein BASIC SET - gesendet.
Gruppen-Nummer | Max. Anzahl Geräte | Beschreibung |
---|---|---|
1 | 1 | WA00Z-1 supports Group 1 for lifeline communication. Group 1 must be assigned the Node ID of the controller to which unsolicited notications will be sent. The Z-Wave controller should set this association automatically after inclusion. Lifeline association only supports the manual reset event. Please refer to the instructions manual of your remote controller or gateway for detail procedures on how these function can be set. |
2 | 5 | WA00Z-1 supports Group 2 with up to five devices as assciation group. Press and Release the top/bottom button, the devices in Group 2 will be turned ON/OFF.Press and hold the top/bottom button, the devices in Group 2 will be dim up/down. |
3 | 5 | WA00Z-1 supports Group 3 with up to five devices as assciation group. Press and Release the top/bottom button twice (double click), the devices in Group 3 will be turned ON/OFF.Press the top/bottom button twice while holding down the top/bottom button in second press, the devices in Group 3 will be dim up/down. |
Z-Wave Produkte können direkt nach der Inklusion im Netz verwendet werden. Durch Konfigurationseinstellungen kann das Verhalten des Gerätes jedoch noch besser an die Anforderungen der Anwendung angepasst und zusätzliche Funktionen aktiviert werden.
WICHTIG: Manche Steuerungen erlauben nur die Konfiguration von vorzeichenbehafteten Werten zwischen -128 und 127. Um erforderliche Werte zwischen 128 und 255 zu programmieren, muss der gewünschte Wert minus 256 eingegeben werden. Beispiel: um einen Parameter auf einen Wert von 200 zu setzen, müsste der Wert 200-256 = -56 eingegeben werden, wenn nur positive Werte bis 128 akzeptiert werden. Bei Werten von 2 Byte Länge wird die gleiche Logik angewandt: Werte über 32768 werden als negative Werte angegeben.
The Valid Values can be set from 0 to 99.Each Valid Value can turn on two scenes. If the Valid Value is set to N, top button is assigned to control 2N+1 scene, and bottom button is assigned to control 2N+2 scene.For example, if the value is set as 4, Scene #7 will be activated when top button is pressed, Scene #8 will be activated when bottom button is pressed. Grösse: 1 Byte, Voreingestellt: 0
Wert | Beschreibung |
---|---|
0 - 99 | ZSC control scene through central scene command class |
User can set the WA00Z-1 to control other devices or they issue various scene activation commands to a central controller. When Value = 0, WA00Z-1 can activate the Scene which is pre-set by Gateway, and then control the associated Smart Bulbs in either Group 2 or Group 3. When Value = 1, WA00Z-1 can only activate the Scene which is pre-set by Gateway.When Value = 2, WA00Z-1 can only control Smart Bulbs in Association Group 2 and Group 3. Grösse: 1 Byte, Voreingestellt: 0
Wert | Beschreibung |
---|---|
0 - 2 | Issue varies scene activation commands to a central controller |
User can set the value to be 1, the function of top/bottom button will be reversed. Grösse: 1 Byte, Voreingestellt: 0
Wert | Beschreibung |
---|---|
0 - 1 | Reverse Button |
Z-Wave Hardware Platform | ZM5202 |
Gerätetyp | Wall Controller |
Netzwerkfunktion | Portable Slave |
Firmware Version | HW: 255 |
Z-Wave Version | 6.51.06 |
Zertifizierungs-ID | ZC10-15100009 |
Z-Wave Produkt Id | 0x020E.0x5343.0x3132 |
Frequenz | XXfrequency |
Maximale Sendeleistung | XXantenna |