Dies ist ein
The sensor must be added to a Z-Wave network prior to use. To include the sensor in a network both the sensor and the network controller must be in inclusion mode at the same time. Refer to the instructions provided by the manufacturer of your specific controller for details on initiating the controllers inclusion mode. STEP ONE Start by placing the controller into inclusion mode.STEP TWOActivate inclusion mode for the sensor by removing the plastic pull-tab from the back of the sensor.When theinclusion process is complete, the LED on the sensor will be solid blue, then go out.STEP THREETest the sensor.Place the magnet next to the sensor to represent a closed position (see Installation section to see where to position the magnet).If the LED flashes ONE TIME, it is successfully communicating on your Zwave network.If the LED on the sensor flashes slow and steady for 5 seconds, you need to repeat the inclusion process.
Z-Wave ist der internationale Funkstandard zur Kommunikation von Geräten im intelligenten Haus. Dies ist ein Z-Wave Gerät und nutzt die im Quickstart angegebene Funkfrequenz.
Z-Wave ermöglicht eine sichere und stabile Kommunikation indem jede Nachricht vom Empfänger rückbestätigt wird (Zweiwege-Kommunikation) und alle netzbetriebenen Geräte Nachrichten weiterleiten (Routing) können, wenn eine direkte Funkbeziehung zwischen Sender und Empfänger gestört ist.Dank Z-Wave können Produkte unterschiedlicher Hersteller miteinander in einem Funknetz verwendet werden. Damit ist auch dieses Produkt mit beliebigen anderen Produkten anderer Hersteller in einem gemeinsamen Z-Wave Funknetz einsetzbar.
Wenn ein Gerät die spezielle sichere Kommunikation unterstützt dann wird es immer dann mit einem anderen Gerät sicher kommunizieren, wenn dieses Gerät auch eine sichere Kommunikation unterstützt. Ansonsten wird aus Kompatibilitätsgründen auf einen normalen Kommunikation umgeschaltet.
Weitere Informationen wie Produktneugkeiten, Tutorials, Supportforen etc. erhalten Sie auf www.zwave.de.
Includes Brown & White coversSleek design virtually disappearsEasy-to-open case requires no special toolsCase tamper protectionIdeal for double-hung windowUp to 3 year battery life on 1 CR123A lithium batteryUses rare earth magnet for up to 5/8th inch gap detectionIncludes white and brown cases
Bitte lesen Sie die Benutzeranleitung bevor Sie das Gerät in Betrieb nehmen.
Damit ein Z-Wave zu einem neuen Netz hinzugefügt werden kann muss es sich im Auslieferungs- oder Reset-Zustand befinden. Im Zweifel ist es sinnvoll, eine Exklusion durchzuführen, um das Gerät ganz sicher in diesem Zustand zu bringen. Diese Exklusion kann von jedem beliebigen Z-Wave Controller durchgeführt werden.
Dieses Gerät kann auch ohne Hilfe eines Controller in den Reset-Zustand zurückgeführt werden. Dies sollte jedoch nur dann gemacht werden wenn der Primärcontroller des Z-Wave-Netzes nicht mehr verfügbar oder defekt ist.
To restore this sensor to factory default settings, follow the instructions in this manual to exclude this sensor from the Z-Wave network. Upon completion of removal from the network the sensor will restore itself to factory default settings automatically.Use this procedure only in the event that the network primary controller is missing or otherwise inoperable.
Im Auslieferungszustand ist das Gerät mit keinem Z-Wave-Netz verbunden. Damit es
mit anderen Z-Wave Geräten kommunizieren kann, muss es in ein bestehendes Z-Wave Netz
eingebunden werden. Dieser Prozess wird bei Z-Wave Inklusion genannt. Geräte können
Netzwerke auch wieder verlassen. Dieser Prozess heißt bei Z-Wave Exklusion. Beide
Prozesse werden von einem Controller gestartet, der dazu in einen Inklusion- bzw.
Exklusion-Modus geschaltet werden muss. Das Handbuch des Controllers enthält
Informationen, wie er in diese Modi zu schalten ist. Erst wenn der Controller
des Z-Wave Netzes im Inclusion-Modus ist, können Geräte hinzugefügt werden.
Das Verlassen des Netzes durch Exklusion führt zum Rücksetzen dieses Gerätes
in den Auslieferungszustand.3>
Das Gerät ist batteriegespeist und damit in der Regel in einem Tiefschlafmodus um
Strom zu sparen. Im Tiefschlafmodus kann das Gerät keine Funksignale empfangen. Daher
wird ein (statischer) Controller benötigt, der netzgespeist und damit immer
funkaktiv ist. Dieser Controller - zum Beispiel ein IP-Gateway - verwaltet eine
Nachrichten-Mailbox für dieses batteriegespeiste Gerät, in dem Nachrichten an dieses
Gerät zwischengespeichert werden. Ohne einen solchen statischen Controller wird die
Nutzung dieses batteriebetriebenen Gerätes sehr schnell zur Entladung der Batterie
führen oder die Nutzung ist komplett unmöglich. Dieses Gerät weckt regelmäßig auf, meldet dies durch Aussenden einer sogenannten
Wakeup-Notifikation und leert dann seine Mailbox im statischen Controller. Dafür
muss bei der Inclusion die Node-ID des Controllers und ein Aufweckinterval
definiert werden. Erfolgt die Inklusion durch einen statischen Controller
wie zum Beispiel ein IP-Gateway, wird dieser Controller diese Konfiguration
automatisch erledigen und in der Regel eine Nutzerschnittstelle anbieten, um das
Aufweck-Interval den Nutzerbedürfnissen anzupassen. Das Aufweckinterval ist ein
Kompromiss zwischen maximaler Batterielaufzeit und minimaler Reaktionszeit des
batteriegespeisten Gerätes. Um das Gerät manuell aufzuwecken, führen Sie die folgende Aktion durch:
The sensor will wake up every so often and when the case is closed to send a Wake-Up Notification to allow the life line master node controller that the sensor is now available for any queued messages that the controller may have for the sensor. The time between Wake-Up Notifications can be configured with the Wake-Up Notification command class to be between 1 hour and 1 week with interval steps of 200 seconds. Inklusion
The sensor must be added to a Z-Wave network prior to use. To include the sensor in a network both the sensor and the network controller must be in inclusion mode at the same time. Refer to the instructions provided by the manufacturer of your specific controller for details on initiating the controllers inclusion mode. STEP ONE Start by placing the controller into inclusion mode.STEP TWOActivate inclusion mode for the sensor by removing the plastic pull-tab from the back of the sensor.When theinclusion process is complete, the LED on the sensor will be solid blue, then go out.STEP THREETest the sensor.Place the magnet next to the sensor to represent a closed position (see Installation section to see where to position the magnet).If the LED flashes ONE TIME, it is successfully communicating on your Zwave network.If the LED on the sensor flashes slow and steady for 5 seconds, you need to repeat the inclusion process.
Exklusion
Exclusion mode on the senor is initiated following the same exact procedure as inclusion.
Kommunikation zu einem schlafenden Gerät (Wakeup)
Die folgenden kleinen Hinweise können bei Problemen im Z-Wave Netz helfen.
Z-Wave Geräte können andere Geräte direkt steuern. Diese direkte Steuerung heißt in Z-Wave Assoziation. In den steuernden Geräten muss dazu die Geräte-ID des zu steuernden Gerätes hinterlegt werden. Dies erfolgt in sogenannten Assoziationsgruppen. Eine Assoziationsgruppe ist immer an ein Ereignis im steuernden Gerät gebunden (Tastendruck oder Auslösen eines Sensors). Bei Eintritt dieses Ereignisses wird an alle in einer Assoziationsgruppe hinterlegten Geräte ein Steuerkommando - meist ein BASIC SET - gesendet.
Gruppen-Nummer | Max. Anzahl Geräte | Beschreibung |
---|---|---|
1 | 5 | This sensor has two Association groups of 5 nodes each. Group one is a lifeline group who will receive unsolicited messages relating to door/window open/close notifications, case tampering notifications, low-battery notifications, and sensor binary reports. |
2 | 5 | Group 2 is intended for devices that are to be controlled i.e. turned on or off (on only by default) with a Basic Set. On inclusion the controller should put its node ID in group 1 but not group 2. |
Z-Wave Produkte können direkt nach der Inklusion im Netz verwendet werden. Durch Konfigurationseinstellungen kann das Verhalten des Gerätes jedoch noch besser an die Anforderungen der Anwendung angepasst und zusätzliche Funktionen aktiviert werden.
WICHTIG: Manche Steuerungen erlauben nur die Konfiguration von vorzeichenbehafteten Werten zwischen -128 und 127. Um erforderliche Werte zwischen 128 und 255 zu programmieren, muss der gewünschte Wert minus 256 eingegeben werden. Beispiel: um einen Parameter auf einen Wert von 200 zu setzen, müsste der Wert 200-256 = -56 eingegeben werden, wenn nur positive Werte bis 128 akzeptiert werden. Bei Werten von 2 Byte Länge wird die gleiche Logik angewandt: Werte über 32768 werden als negative Werte angegeben.
Parameter 1 configures the sensor to send or not send Basic Set commands of 0x00 to nodes in Association group2 turning the devices off when the sensor is in a restored state i.e. the door is closed. By default the sensor does NOT send Basic Set commands of 0x00. Grösse: 1 Byte, Voreingestellt: 0
Wert | Beschreibung |
---|---|
-1 - 0 | 0x00 off, 0xFF on |
Parameter 2 configures the sensor to either to send or not to send Sensor Binary Report commands to Association Group 1 when the sensor is faulted andrestored. If the controller is fully compatible with the Notification Command Class thereby making the Sensor Binary Reports redundant, the controller candisable the Sensor Binary Report Commands completely. Grösse: 1 Byte, Voreingestellt: 0
Wert | Beschreibung |
---|---|
-1 - 0 | 0x00 off, 0xFF on |
Z-Wave Hardware Platform | ZM5202 |
Gerätetyp | Notification Sensor |
Netzwerkfunktion | Reporting Sleeping Slave |
Firmware Version | HW: 2 FW: 10.01 |
Z-Wave Version | 6.51.06 |
Zertifizierungs-ID | ZC10-18056109 |
Z-Wave Produkt Id | 0x014A.0x0004.0x0002 |
Sensors | |
Supported Notification Types | |
Frequenz | XXfrequency |
Maximale Sendeleistung | XXantenna |