Dies ist ein
Add(Including) alarm to Z-Wave Network1:Make sure the battery is installed well before operating the product. 2:Make sure the alarm is on its final install location, then set the controller into the Add(Inclusion )mode.3:Quickly, triple click the test button, The LED will light up.4:Issued beep, LED off, the alarm being Add (included)to the network successfully.
Z-Wave ist der internationale Funkstandard zur Kommunikation von Geräten im intelligenten Haus. Dies ist ein Z-Wave Gerät und nutzt die im Quickstart angegebene Funkfrequenz.
Z-Wave ermöglicht eine sichere und stabile Kommunikation indem jede Nachricht vom Empfänger rückbestätigt wird (Zweiwege-Kommunikation) und alle netzbetriebenen Geräte Nachrichten weiterleiten (Routing) können, wenn eine direkte Funkbeziehung zwischen Sender und Empfänger gestört ist.Dank Z-Wave können Produkte unterschiedlicher Hersteller miteinander in einem Funknetz verwendet werden. Damit ist auch dieses Produkt mit beliebigen anderen Produkten anderer Hersteller in einem gemeinsamen Z-Wave Funknetz einsetzbar.
Wenn ein Gerät die spezielle sichere Kommunikation unterstützt dann wird es immer dann mit einem anderen Gerät sicher kommunizieren, wenn dieses Gerät auch eine sichere Kommunikation unterstützt. Ansonsten wird aus Kompatibilitätsgründen auf einen normalen Kommunikation umgeschaltet.
Weitere Informationen wie Produktneugkeiten, Tutorials, Supportforen etc. erhalten Sie auf www.zwave.de.
The unit is a photoelectric 3V DC smoke and heat alarm. It is operated by 3v AA Alkaline battery. With the photoelectric technology, it is more sensitive in detecting slow smoldering fires which generate light smoke. little heat and may smolder for hours before bursting into flames. This smoke alarm does not contain any radioactive material.The smoke alarm is an intelligent security equipment that can be controlled by the Z-Wave network which has particular frequency. Different countries or areas, the radio frequency of the Z-Wave is different. This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. In the Z-Wave network communications, the smoke alarm can communicate with other devices associated. When the smoke is detected, the sensor will send messages to the main controller, and then the alarm sound. Through the Z-Wave network, the devices associated can response after smoke is detected, For instance , Start fire extinguishing equipment and trigger an alarm, Through the Z-Wave network controller, You will be notified in case of fire.
Bitte lesen Sie die Benutzeranleitung bevor Sie das Gerät in Betrieb nehmen.
Damit ein Z-Wave zu einem neuen Netz hinzugefügt werden kann muss es sich im Auslieferungs- oder Reset-Zustand befinden. Im Zweifel ist es sinnvoll, eine Exklusion durchzuführen, um das Gerät ganz sicher in diesem Zustand zu bringen. Diese Exklusion kann von jedem beliebigen Z-Wave Controller durchgeführt werden.
Dieses Gerät kann auch ohne Hilfe eines Controller in den Reset-Zustand zurückgeführt werden. Dies sollte jedoch nur dann gemacht werden wenn der Primärcontroller des Z-Wave-Netzes nicht mehr verfügbar oder defekt ist.
Reset will delete all information on the Z-Wave network controller, and restore the alarm to factory default settings. 1: Press and hold the test button , Installing the battery, red LED light, until the LED is off, release the button, LED light up again, press the button again, When hearing a beep, restore factory settings successfully.Note: If this sensor is reset, the information of Z-Wave network in the sensor will be deleted. The sensor will be itself restored to factory default settings. Please use this procedure only when the network primary controller is missing or otherwise inoperable.
Im Auslieferungszustand ist das Gerät mit keinem Z-Wave-Netz verbunden. Damit es
mit anderen Z-Wave Geräten kommunizieren kann, muss es in ein bestehendes Z-Wave Netz
eingebunden werden. Dieser Prozess wird bei Z-Wave Inklusion genannt. Geräte können
Netzwerke auch wieder verlassen. Dieser Prozess heißt bei Z-Wave Exklusion. Beide
Prozesse werden von einem Controller gestartet, der dazu in einen Inklusion- bzw.
Exklusion-Modus geschaltet werden muss. Das Handbuch des Controllers enthält
Informationen, wie er in diese Modi zu schalten ist. Erst wenn der Controller
des Z-Wave Netzes im Inclusion-Modus ist, können Geräte hinzugefügt werden.
Das Verlassen des Netzes durch Exklusion führt zum Rücksetzen dieses Gerätes
in den Auslieferungszustand.3>
Inklusion
Add(Including) alarm to Z-Wave Network1:Make sure the battery is installed well before operating the product. 2:Make sure the alarm is on its final install location, then set the controller into the Add(Inclusion )mode.3:Quickly, triple click the test button, The LED will light up.4:Issued beep, LED off, the alarm being Add (included)to the network successfully.
Exklusion
1: Make sure the battery is installed well before operating the product.2: Set the Z-Wave Network controller into Remove(exclusion) mode.3:Quickly, triple click the test button, The LED will light up and alarm enter Remove(Excluding) Mode.4:Wait for the main controller to Remove(exclusion) the alarm.Note: If the alarm is Remove(excluded), then the sensor will be itselfrestored to factory default settings.
Die folgenden kleinen Hinweise können bei Problemen im Z-Wave Netz helfen.
Z-Wave Geräte können andere Geräte direkt steuern. Diese direkte Steuerung heißt in Z-Wave Assoziation. In den steuernden Geräten muss dazu die Geräte-ID des zu steuernden Gerätes hinterlegt werden. Dies erfolgt in sogenannten Assoziationsgruppen. Eine Assoziationsgruppe ist immer an ein Ereignis im steuernden Gerät gebunden (Tastendruck oder Auslösen eines Sensors). Bei Eintritt dieses Ereignisses wird an alle in einer Assoziationsgruppe hinterlegten Geräte ein Steuerkommando - meist ein BASIC SET - gesendet.
Gruppen-Nummer | Max. Anzahl Geräte | Beschreibung |
---|---|---|
1 | 4 | Z-Wave Plus Lifeline |
2 | 4 | Linkage group 2 is assigned to the devices status - sending BASIC SET control frameto the associated devices having detected the smoke alarm. |
3 | 4 | Linkage group 3 reports the detection's status to the associated device. smoke alarm |
4 | 4 | Linkage group 4 is assigned to the devices status - sending BASIC SET control frameto the associated devices having detected the heat alarm. |
5 | 4 | Linkage group 5 reports the detection's status to the associated device. |
Z-Wave Hardware Platform | ZM5202 |
Gerätetyp | Notification Sensor |
Netzwerkfunktion | Reporting Sleeping Slave |
Firmware Version | HW: 255 FW: 1.01:01.01 |
Z-Wave Version | 6.71.00 |
Zertifizierungs-ID | ZC10-17095785 |
Z-Wave Produkt Id | 0x0266.0x0005.0x0001 |
Supported Notification Types | |
Security V2 | S2_UNAUTHENTICATED |
Frequenz | XXfrequency |
Maximale Sendeleistung | XXantenna |